Valtra 6550 - Page 504

125
Model Code Page
37. Autocontrol 5
1. 8. 2000
370 9B
6250--8950
1. 9. 2002
Main program no. 60 (J38343---K02115).
These can be replaced with program version 65
.
ThesemustnomorebeusedinService.
10 60 PTO 1000
17 60 PTO 1000/540E
51 60 PTO 540/1000
57 60 PTO 540/540E
71 60 PTO 540E/1000E (8350Hi)
NumbersusedonlybyServiceandSpareParts
.
22 60
3)
6250Hi ---8950Hi (Ei 8350Hi)
32 60
3)
8350Hi
Main program no. 62 (J38343---K41106).
These can be replaced with program version 65
.
ThesemustnomorebeusedinService.
10 62 PTO 1000
17 62 PTO 1000/540E
51 62 PTO 540/1000
57 62 PTO 540/540E
71 62 PTO 540E/1000E (8350Hi)
NumbersusedonlybyServiceandSpareP
arts.
20 62
3)
6250Hi ---8950Hi (Ei 8350Hi)
23 62 6250Hi --- 8950Hi (Ei 8350Hi)
30 62
3)
8350Hi
33 62 8350Hi
Main program no. 63 (J38343---K41106).
Used only in service in some tractors.
Thesemustbereplacedwithprogramversion65
.
These must not be used in Service .
23 63
3)
6250Hi ---8950Hi (Ei 8350Hi)
33 63
3)
8350Hi
Main program no. 64 (J38343---K41106).
NumbersusedonlybyServiceandSpareParts.
These can be replaced with program version 65
.
ThesemustnomorebeusedinService.
23 64 6250Hi --- 8950Hi (Ei 8350Hi)
33 64 8350Hi
Main program no. 65 (J38343---K41106).
NumbersusedonlybyServiceandSpareParts.
Thesemustbeusedinservice
These programs are in disk 340 422 60.
23 65 6250Hi --- 8950Hi (Ei 8350Hi)
33 65 8350Hi
Main program no. 66 (J38343---K41106).
Used only in service in some tractors.
Thesemustbereplacedwithprogramversion65
.
These must not be used in Service .
23 66
3)
6250Hi ---8950Hi (Ei 8350Hi)
33 66
3)
8350Hi
1) A new program must be input into the co ntrol unit in
connection with service (main program version 53).
2) If a tractor has the reverse drive controls, a new pro-
gram must be input (main program version 65). Affects
function of the clutch pedal and AutoDPS when the
seat is turned rearwards.
3) A new program must be input (main pro gram version
65).
Note! If in the test mode FII the I.D. number is 9953 or
9965 after programming or after control unit change,
the parameter file has not been input. Input correct
parameter file according to instr. on page 370---24B.
Note! If the clutch pedal has malfunctions or the tractor has
malfunctions (e. g. fault codes P101...P109), the trans-
mission has jammed or if tractors transmission has not dis-
engagedcompletywithclutchpedal,withHiShiftbuttonor
with shuttle lever, then must a new program be input (main
program version 53 or 65 and parameter file). Program-
ming instructions on page 370---24B.