18-5
IM 701240-01E
Specifications
3
2
1
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Recorder Mode
Item Specifications
Realtime recording on T-Y waveform recording/numeric value recording: Output to the chart in realtime.
the built-in printer X-Y Waveform Recording: Starts the data acquisition with START and
generates X-Y waveforms in realtime. Outputs X-
Y waveforms to the chart with STOP.
Length of data saved to T-Y waveform recording: Fixed to 2.5 MW. Automatically saves up to 1000 divisions of data
memory while realtime (depending on the chart speed).
recording X-Y waveform recording: Fixed to 1 MW.
Recording start trigger Recording can be started using a trigger by setting the trigger mode.
Auto: Trigger disabled. Continuous recording. Recording starts with measurement start.
Log: Trigger disabled. Recording stops when the memory storage length of data is acquired.
When short recording is specified, recording stops when shot recording ends.
Single: Trigger enabled. Recording starts after a trigger detection.
When short recording is specified, recording stops when shot recording ends.
Repeat: Trigger enabled. Recording starts after a trigger detection.
Selectable only when shot recording is specified. Reenters trigger-wait state after short
recording.
Chart speed 20 mm/s, 10 mm/s, 5 mm/s, 2 mm/s, 1 mm/s100 mm/min, 50 mm/min, 25 mm/min, 20 mm/min,
(T-Y waveform recording) 10 mm/min, 5 mm/min, 2 mm/min, 1 mm/min, 100 mm/h, 50 mm/h, 25 mm/h, 20 mm/h, 10 mm/h
Output interval 1 s, 2 s, 5 s, 10 s, 15 s, 20 s, 30 s, 1 min, 2 min, 5 min, 10 min, 15 min, 20 min, 30 min, 60min
(Numeric value recording)
Sample rate during X-Y 5 kS/s, 2 kS/s, 1 kS/s, 500 S/s, 200 S/s, 100 S/s, 50 S/s, 20 S/s, 10 S/s, 5S/s
waveform recording
Recording format T-Y waveform recording: 1 division recording 200 mm/zone or 160 mm/zone (flexible zone is
selectable for 1 division recording)
2 zone recording 80 mm/zone or 100 mm/zone
3 zone recording 60 mm/zone or 65 mm/zone
4 zone recording 40 mm/zone or 50 mm/zone
8 zone recording 20 mm/zone
16 zone recording 10 mm/zone
Numeric value recording: Print direction selectable from standard and 180° rotation.
X-Y waveform recording: Records up to 4 waveforms simultaneously. Assignment of X and Y
channels on the 4 waveforms is arbitrary.
Grid Width: Selectable from 1 div and 10 mm.
Type: Selectable from two types and OFF.
Density: Dark/Light selectable.
Recorded contents Simultaneously prints, scale, channel label, graticule, timestamp, gauge, annotation, etc.
During T-Y waveform recording
Scale: Prints the scale value for each channel. Select the print interval from OFF, 200,
400, and 800 mm.
Channel label: Prints channel labels near the waveforms. Select the print interval from OFF,
200, 400, and 800 mm.
Time print: Prints the recording start time and timestamps. Select the print interval from OFF,
200, 400, and 800 mm.
Gauge: Prints the scale value for each channel and the end of printing.
Annotation: Select channel information, channel message, or Data to be printed.
Channel information: Prints information such as measurement range, and
filter.
Message: Prints a preset message string.
Data: Prints numeric measured values.
Select the print interval from OFF, 200, 400, and 800 mm.
During X-Y waveform recording
Prints the scale value.
Shot recording Automatically stops when the specified length is recorded after the start of measurement or after the
trigger condition is met.
Shot recording length: Continuous, 20 cm, 50 cm, 1m, or 2 m
External start/stop Prints on a low signal. Stops printing on a high signal.
Reprint function An arbitrary section of the recorded data saved to the memory simultaneously with realtime print
can be reprinted in an arbitrary format.
Print image output When performing reprint or fine print during T-Y waveform recording, the print image can be
converted and output to a PDF file.
18.5 Function
To Next Page
Loading...
