Entron EN1000 series

ENTRON Controls, LLC. • 700120S • Page 129
REMEDY
Wait for the Temperature
Limit Switch to cool or check
for open circuit. See Section
4.3, 4.5, and 5.4.6.
Two Stage Operation not
allowed with FS7. See
Section 4.3 and 4.4.
Two Stage Operation not
allowed with FS11. See
Section 4.3 and 4.4.
Return to OPERATE mode.
See Section 2.1 and 6.0.
Initiations must be open at
power on or after an
Emergency Stop. See Section
1.1, 4.3, and 4.4.
Open TS1-TLS1/AUX1. See
Section 4.3, 4.5, and 5.4.6.
Open TS1-FS1. See Section
4.3, 4.5, 5.4.3, and 9.6.
Open TS1-FS3. See Section
4.3, 4.5, 5.4.3, and 9.6.
Open TS1-FS7. See Section
4.3, 4.5, 5.4.3, and 9.6.
Open TS1-FS11. See Section
4.3, 4.5, 5.4.3, and 9.6.
Replace Control Board.
Replace Control Board.
Change to higher welding
transformer tap. See Section
5.4.10.
11.0 ERROR CODES AND TROUBLESHOOTING
Please refer to other manual pages and Wiring Diagrams for location of fuses, terminal strips, etc.
11.1 ERROR CODES
ERROR
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0101
0101
01
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0202
0202
02
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0303
0303
03
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0404
0404
04
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0505
0505
05
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0606
0606
06
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0707
0707
07
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0808
0808
08
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
0909
0909
09
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
1010
1010
10
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
11
11
1
11
11
1
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
1212
1212
12
Data/Schedule
Display
E.rE.r
E.rE.r
E.r
..
..
.=
1313
1313
13
POSSIBLE CAUSE
Error Code #01
Temperature Limit Switch open or
overheated.
Error Code #02
FS1 AND FS7 both closed.
Error Code #03
FS1 AND FS11 both closed.
Error Code #04
Attempt to weld in PROGRAM mode.
Error Code #05
FS1,FS3,FS7,FS11 closed to GND before
power on or before Emergency Stop is re-
closed after being opened.
Error Code #06
Back-step or Retraction is closed too long
or at start of sequence.
Error Code #07
FS1 initiated while another seq. active.
Error Code #08
FS3 initiated while another seq. active.
Error Code #09
FS7 initiated while another seq. active.
Error Code #10
FS11 initiated while another seq. active.
Error Code #11
Control Board. Control Relay problem.
Error Code #12
Control Board. Hardware error.
Error Code #13
Full conduction detected.