Entron EN1000 series

ENTRON Controls, LLC. • 700120S • Page 47
The available EXTENDED FUNCTION parameters are listed below – they are described in
the indicated sections.
Designation Description Section
I.d.I.d.
I.d.I.d.
I.d. Identification Number 5.4.1
S.E.S.E.
S.E.S.E.
S.E. Seam Welding Mode 5.4.2
S.S.S.S.
S.S.S.S.
S.S. Schedule Select 5.4.3
C.C.C.C.
C.C.C.C.
C.C. Automatic Voltage Compensation & Monitoring 5.4.4
C.A.C.A.
C.A.C.A.
C.A. Clear All Functions 5.4.5
b.S.b.S.
b.S.b.S.
b.S. Back-Step / Temperature Limit Switch 5.4.6
PP
PP
P
.O..O.
.O..O.
.O. Process Outputs 5.4.7
b.E.b.E.
b.E.b.E.
b.E. Beat Operation Initiation Modes 5.4.8
8.7.8.7.
8.7.8.7.
8.7. 87° Delay 5.4.9
PP
PP
P
.P.P
.P.P
.P
..
..
. Manual Power Factor Programming 5.4.10
PP
PP
P
.F.F
.F.F
.F
..
..
. Power Factor Measuring 5.4.11
S.d.S.d.
S.d.S.d.
S.d. Squeeze Delay 5.4.12
b.L.
b.L.
b.L.b.L.
b.L. Blocking Delay (if
PP
PP
P
.O..O.
.O..O.
.O.=
0707
0707
07 only) 5.4.13
t.rt.r
t.rt.r
t.r
..
..
. Turns Ratio 5.4.14
C.rC.r
C.rC.r
C.r
..
..
. Constant Current Modes 5.4.15
rr
rr
r
.A..A.
.A..A.
.A. Range 5.4.16
C.O.C.O.
C.O.C.O.
C.O. Current Offset 5.4.17
S.t.S.t.
S.t.S.t.
S.t. Stepper 7.0
PP
PP
P
.C..C.
.C..C.
.C. Pressure Control Mode
b.d.b.d.
b.d.b.d.
b.d. Background Pressure
S.I.S.I.
S.I.S.I.
S.I. Sensor Input
PP
PP
P
.n..n.
.n..n.
.n. PIN Lockout Mode 5.4.18
5.4.1 IDENTIFICATION NUMBER –
I.d.I.d.
I.d.I.d.
I.d.
The EN1000/EN1001 Control may be equipped with RS485 Option to communicate to a PC or
any other device with RS485 interface. The device with RS485 interface is capable of
communicating with up to 64 controls on a common two-wire network. For this reason the
control needs to be identified. See Instruction Manual 700171 for more information.
5.4.2 SEAM WELDING MODE –
S.E.S.E.
S.E.S.E.
S.E.
To program the control for SEAM operation:
1. Put the control in PROGRAM mode.
2. Use SELECT to find
EFEF
EFEF
EF.
3. Use the SCHEDULE push buttons to scroll through EXTENDED FUNCTIONS and
find
S.E.S.E.
S.E.S.E.
S.E.
5.4 EXTENDED FUNCTIONS (cont.)
Available only for EN1001
using Constant Current
Available only if IPSC
hardware is present
See Instruction
Manual 700178
for IPSC