Entron EN1000 series

ENTRON Controls, LLC. • 700120S • Page 65
PP
PP
P
.O..O.
.O..O.
.O.=
2222
2222
22 Send HI/LO and CURRENT after out of limit window weld or last weld in
sequence with RS232 or RS485 Option (EN1001 ONLY) – Will send data for out
of limit window weld in sequence or last weld only in completed sequence to
master on ENBUS or to serial printer. Display will flash
H.i.H.i.
H.i.H.i.
H.i. or
L.o.L.o.
L.o.L.o.
L.o. and measured
CURRENT if out of limit window.
PP
PP
P
.O..O.
.O..O.
.O.=
2323
2323
23 Send HI/LO and CURRENT if current out of limit window with RS232 or RS485
Option (EN1001 ONLY) – Will send data after weld if the current is out of limit
window to master on ENBUS or to serial printer. Display will flash
H.i.H.i.
H.i.H.i.
H.i. or
L.o.L.o.
L.o.L.o.
L.o.
and measured CURRENT.
PP
PP
P
.O..O.
.O..O.
.O.=
2424
2424
24 Flash and indicate
H.i.H.i.
H.i.H.i.
H.i./
L.o.L.o.
L.o.L.o.
L.o. if current out of limit window and show CURRENT
(EN1001 ONLY) – Uses Valve 1 to indicate HIGH current errors, Valve 2 for LOW
current errors, and Valve 3 to indicate END OF SEQUENCE, displays measured
CURRENT on DATA display after END OF SEQUENCE and displays
H.i.H.i.
H.i.H.i.
H.i. or
L.o.L.o.
L.o.L.o.
L.o.
if measured current is out of HIGH/LOW limit window.
PP
PP
P
.O..O.
.O..O.
.O.=
2525
2525
25 Indicate
H.i.H.i.
H.i.H.i.
H.i./
L.o.L.o.
L.o.L.o.
L.o. and EOS; show CURRENT on DATA display (EN1001 ONLY)
– Uses Valve 1 to indicate HIGH current errors, Valve 2 for LOW current errors, and
Valve 3 to indicate END OF SEQUENCE, and will display measured CURRENT
on DATA display after END OF SEQUENCE.
PP
PP
P
.O..O.
.O..O.
.O.=
2626
2626
26 Flash
H.i.H.i.
H.i.H.i.
H.i./
L.o.L.o.
L.o.L.o.
L.o., stop sequence in HOLD, holding part if current out of limit
window (EN1001 ONLY) – Uses Valve 3 to indicate HIGH or LOW current errors
and stop the sequence until the error is cleared. Valve 1, if programmed, may be
used to hold the part after the weld. Refer to Section 9.7 for more information.
PP
PP
P
.O..O.
.O..O.
.O.=
2727
2727
27 Flash
H.i.H.i.
H.i.H.i.
H.i./
L.o.L.o.
L.o.L.o.
L.o., break sequence, and turn Valve 3 ON if current out of limit
window (EN1001 ONLY) – The same as
PP
PP
P
.O..O.
.O..O.
.O.=
1414
1414
14, except that Valve 3 output will be
ON for 0.5 seconds to indicate HIGH or LOW current.
PP
PP
P
.O..O.
.O..O.
.O.=
2828
2828
28 Indicate EOS and turn Valve 3 ON if current within limit window and control
in WELD mode and closed NW1-GND input on TS1 (EN1001 ONLY) – Valve 3
will be ON for 0.5 seconds at END OF SEQUENCE to indicate that current was
within the HIGH/LOW limit window, and if control was in WELD mode with
closed NW1-GND input on TS1. In NON-CONSTANT CURRENT mode, this
PROCESS OUTPUT will turn Valve 3 ON for 0.5 seconds after EOS only if control
was in WELD mode and closed NW1-GND input.
PP
PP
P
.O..O.
.O..O.
.O.=
3030
3030
30 ON if ERROR
3636
3636
36 (IPSC or IPS error) occurs – When the control includes the
IPSC or IPS option, the control may be programmed to turn Valve 3 ON to indicate
whenever any PRESSURE error is detected.
PP
PP
P
.O..O.
.O..O.
.O.=
3131
3131
31 ON if ERROR
3636
3636
36 (IPSC or IPS error) occurs at end of weld – When the control
includes the IPSC or IPS option and uses this PROCESS OUTPUT, the control
reads the sensor output after the WELD portion of the weld sequence and turns the
Valve 3 ON if the TRIGGER value for PRESSURE/FORCE/CURRENT is not
reached. The TRIGGER values must be programmed within a valid range.
5.4.7 PROCESS OUTPUTS –
PP
PP
P
.O..O.
.O..O.
.O. (cont.)