l Management VLAN ID of the cluster, that is 10
l IP address of the SNMP host, that is 3.0.0.1/8
l IP address of VLANIF 10 that is 1.0.0.1/8 and a reachable route between VLANIF 10 and
the SNMP host
l Address pool of the cluster, that is 10.0.0.0/8
l IP address of the administrator switch used in the cluster, that is 10.0.0.1/8
Procedure
Step 1 Configure a management VLAN.
# Create VLAN 10 on the device and add interfaces of the administrator switch and member
switches to VLAN 10.
# Configure the administrator switch.
<Quidway> system-view
[Quidway] sysname Administrator-1
[Administrator-1] vlan 10
[Administrator-1-vlan10] quit
[Administrator-1] interface gigabitethernet 0/0/1
[Administrator-1-GigabitEthernet0/0/1] port link-type trunk
[Administrator-1-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[Administrator-1-GigabitEthernet0/0/1] quit
[Administrator-1] interface gigabitethernet 0/0/2
[Administrator-1-GigabitEthernet0/0/2] port link-type trunk
[Administrator-1-GigabitEthernet0/0/2] port trunk allow-pass vlan 10
[Administrator-1-GigabitEthernet0/0/2] quit
[Administrator-1] interface gigabitethernet 0/0/3
[Administrator-1-GigabitEthernet0/0/3] port link-type trunk
[Administrator-1-GigabitEthernet0/0/3] port trunk allow-pass vlan 10
[Administrator-1-GigabitEthernet0/0/3] quit
[Administrator-1] interface vlanif 10
[Administrator-1-Vlanif10] quit
# Configure member switch 1.
<Quidway> system-view
[Quidway] sysname Member-1
[Member-1] vlan 10
[Member-1-vlan10] quit
[Member-1] interface gigabitethernet 0/0/1
[Member-1-GigabitEthernet0/0/1] port link-type trunk
[Member-1-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[Member-1-GigabitEthernet0/0/1] quit
[Member-1] interface gigabitethernet 0/0/2
[Member-1-GigabitEthernet0/0/2] port link-type trunk
[Member-1-GigabitEthernet0/0/2] port trunk allow-pass vlan 10
[Member-1-GigabitEthernet0/0/2] quit
[Member-1] interface vlanif 10
[Member-1-Vlanif10] quit
# Configure member switch 2.
<Quidway> system-view
[Quidway] sysname Member-2
[Member-2] vlan 10
[Member-2-vlan10] quit
[Member-2] interface gigabitethernet 0/0/1
[Member-2-GigabitEthernet0/0/1] port link-type trunk
[Member-2-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[Member-2-GigabitEthernet0/0/1] quit
[Member-2] interface vlanif 10
[Member-2-Vlanif10] quit
Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management 3 HGMP Configuration
Issue 01 (2011-10-26) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
140
To Next Page
Loading...
