Huawei Quidway S5700 Series User Manual

1. Configure Switch A as the NQA client and create an ICMP jitter test instance on Switch
A.
2. Configure Switch B as the NQA server.
Data Preparation
To complete the configuration, you need the following data:
l IP address of Switch B
Procedure
Step 1 Configure a reachable route between Switch A and Switch B.
The configuration details are not mentioned here.
Step 2 Configure an NQA test instance for Switch A.
# Enable the NQA client and configure the ICMP jitter test instance.
<RouterA> system-view
[RouterA] nqa test-instance admin icmpjitter
[RouterA-nqa-admin-icmpjitter] test-type icmpjitter
[RouterA-nqa-admin-icmpjitter] destination-address ipv4 10.1.1.2
Step 3 Start the test.
[RouterA-nqa-admin-icmpjitter] start now
Step 4 Check test results.
[RouterA-nqa-admin-icmpjitter] display nqa results test-instance admin icmpjitter
NQA entry(admin, icmpjitter) :testflag is inactive ,testtype is icmpjitter
1 . Test 1 result The test is finished
SendProbe:60 ResponseProbe:60
Completion :success RTD OverThresholds number:0
OWD OverThresholds SD number:0 OWD OverThresholds DS number:0
Min/Max/Avg/Sum RTT:1/3/1/65 RTT Square Sum:77
NumOfRTT:60 Drop operation number:0
Operation sequence errors number:0 RTT Stats errors number:0
System busy operation number:0 Operation timeout number:0
Min Positive SD:1 Min Positive DS:1
Max Positive SD:3 Max Positive DS:1
Positive SD Number:18 Positive DS Number:15
Positive SD Sum:22 Positive DS Sum:15
Positive SD Square Sum :32 Positive DS Square Sum :15
Min Negative SD:1 Min Negative DS:1
Max Negative SD:2 Max Negative DS:1
Negative SD Number:21 Negative DS Number:14
Negative SD Sum:22 Negative DS Sum:14
Negative SD Square Sum :24 Negative DS Square Sum :14
Min Delay SD:0 Min Delay DS:0
Max Delay SD:1 Max Delay DS:1
Delay SD Square Sum:4 Delay DS Square Sum:1
Packet Loss SD:0 Packet Loss DS:0
Packet Loss Unknown:0 Average of Jitter:1
Average of Jitter SD:1 Average of Jitter DS:1
jitter out value:0.5599658 jitter in value:0.3574005
NumberOfOWD:60 Packet Loss Ratio: 0%
OWD SD Sum:4 OWD DS Sum:1
ICPIF value: 0 MOS-CQ value: 0
TimeStamp unit: ms
----End
Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management 6 NQA Configuration
Issue 01 (2011-10-26) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
363

Huawei Quidway S5700 Series Specifications

General

Category	Switch
Operating Temperature	0°C to 45°C
Relative Humidity	5% to 95% (non-condensing)
Series	Quidway S5700
Forwarding Performance	Up to 96 Mpps
Ports	24 or 48 x 10/100/1000Base-T ports
Power Supply	AC or DC
Storage Temperature	-40°C to 70°C
Fixed GE Ports	24 or 48
Uplink Ports	4 x GE SFP ports
Routing Protocols	RIP, OSPF, BGP
Management	SNMP, RMON, CLI, Web
VLAN	4094 VLANs
PoE	Optional