Janus JFS-A1 - Cabinet Installation

To Next Page

To Previous Page

Page: 90

JFS-A1 INSTALLATION, OPERATION, AND INSTRUCTION MANUAL

Document #: DOC230

Issued: August 27, 2012

Revised: N/A

Cabinet Installation

e PSN-1000/PSN-1000(E) slides into the guides located at the bottom of the panel, and then secured with

screws as shown in the following illustration.

Figure 117. PSN-1000 Panel Installation Showing Cabinet

DWG #602-22

Main Page

Table of Contents3
Section 1: Introduction11
Purpose of this Manual11
System Overview11
System Features11
P-Link Accessories12
SLC Loop Accessories12
Addressable Sensors12
Addressable Modules13
How to Use this Manual13
Common Terminology13
Section 2: before You Start Installation14
System Specifications14
Environmental Specifications14
System Configurations / Appliances14
Electrical Specifications15
System Size Specifications15
Main Board Wiring Specifications15
Circuit Separation15
Wiring Types16
Cabinet Dimensions16
Cabinet Wiring Connections17
Battery Circuit Calculations17
Battery Calculation Worksheets18
SLC Current Draw Worksheet19
Isolator Device Load Calculation20
Scenario 1: Class a Loop - Isolated Devices Configuration20
Scenario 2: Class B Loop - Isolated Branch Configuration21
Battery Connections22
Main Supply Circuit22
Section 3: Installation23
Signaling Line Circuit (SLC) Installation23
SLC Wiring Requirements23
Class B, Style 4 Wiring Configuration23
Class A, Style 6 Wiring Configuration24
Class A, Style 7 Wiring Configuration25
Connecting Analog Detectors25
Connecting Addressable Modules26
Conventional Initiating Zones (CIZM-4) Class a26
Conventional Initiating Zones (CIZM-4) Class B26
Miniature Contact Module (MCM)27
Single Contact Module - 4 Inch Mount (SCM-4)27
Dual Contact Module - 4 Inch Mount (DCM-4)27
Twin Relay Module - 4 Inch Mount (TRM-4)28
Monitored Output Module - 4 Inch Mount (MOM-4)28
Connecting Analog Sounder Base (ASB)29
Connecting Analog Relay Base (ARB)29
Addressing SLC Devices31
Notification Appliance Circuits Installation32
NAC Wiring32
NAC Maximum Wiring Impedance Formula32
NAC Wiring Configurations32
NAC as Releasing Device Circuit34
Maximum Wire Impedance Formula34
I/O Circuit Configuration35
I/O Circuits as Inputs35
I/O Circuits as Outputs35
I/O Maximum Impedance Formula35
Reverse Polarity Communication Line Circuit36
Municipal Box Connection37
Relay Output Wiring37
CA-6075 Class a Expander Installation38
P-Link Devices39
Configuration Characteristics39
Maximum Wire Resistance Formula39
P-Link Addresses40
Installing Remote Annunciators (RA-6500R and RA-6075R)41
Setting Addresses41
Installing the DACT42
Dip Switch Location43
Section 4: Operation44
Control Panel Basic Operation44
LCD Display44
Menu Navigation Keys45
Numeric Keypad45
Function Pushbuttons45
Status Leds46
Control Panel Menu Tree47
Section 5: Programming48
Programming Options48
Programming Overview51
The Programming Cycle51
Software Installation51
LEARN Programming52
Connecting the Computer and Panel52
Transferring Data54
Uploading from Panel to Computer55
Downloading Configuration File to Panel56
Enable Remote Access56
File New56
File Save / Save as57
Audit Errors57
Uploading History Events & Detector (Sensitivity) Status Reports59
History Reports59
Detector Sensitivity Status Reports60
Printing Reports61
Panel Software Overview62
Window Regions / Areas62
Program Icons63
Programming Functions Overview64
Remote Access Code65
User Name / Password65
General System Functions66
Job Details66
General Options66
Day/Night Sensitivity Mode and Holiday Scheduling67
Users68
System E-Mail Functions68
P-Link E-Mail Notification Requirements70
Connecting the Panel to a Network70
E-Mail Report Programming71
E-Mail Sent from Panel71
E-Mail Report Requested from PC72
Receiving E-Mail Status Reports74
System Programming76
Mapping Zones Overview76
Single Zones76
Multiple Zones76
Mapping Terminology77
Zone Types / Styles77
Zone Attributes78
Releasing Zone Attributes80
Creating Zones80
Configuring Zones81
Configuring Points81
NAC Functions82
SLC Functions83
Adding Points to Zones86
Group by Area88
Cross Zone Configurations89
Releasing Zone Configurations90
Releasing Fields90
Single Interlock (One Count) Releasing Application92
Cross Zone / Two Count (Double Interlock) Releasing Application92
Cross Zone Releasing Application with Abort Switch93
Programming Modules94
Dact (Ud-1000)94
CA-6075 Class a Converter Module96
Remote Annunciators (RA-6500R and RA-6075R)97
Section 6: PSN-1000 / PSN-1000(E) - Installing, Operating & Programming98
Board Specifications98
Cabinet Descriptions98
Visual Indicators98
Environmental Specifications98
Electrical Specifications98
Wiring Specifications98
Circuit Separation98
Wiring Types99
Cabinet Dimensions99
Cabinet Installation100
Cabinet Wiring Connections101
Rechargeable Battery Circuit102
Battery Circuit Calculation102
PSN-1000/PSN-1000(E) Battery Calculation Worksheet103
Notification Appliance Circuits (Nacs)104
NAC Wiring104
NAC Wiring Configurations104
Input Circuits106
Configuration Characteristics106
Wiring to Control Panel107
Repeater Output108
Configuration Characteristics108
Maximum Wire Resistance Formula108
Municipal Box Connection109
Configuration Characteristics109
Relay Outputs109
PSN-1000/PSN-1000(E) Operations110
Status Leds110
PSN-1000/PSN-1000(E) Programming111
Adding a Power Supply111
Deleting a Power Supply112
Section 7: IP Communication113
Programming the IP Communicator114
IP Reporting Accounts114
Appendix A: Basic Operating Instructions116
Appendix B: Modem Connectivity Setup118
Appendix C: System Maintenance and Testing119
Acceptance Test119
Periodic Testing and Service119
Operational Checks119
AC Fuse119
Battery Maintenance120
Replacement and Testing Recommendations120
Proper Handling / First Aid Procedures120
Appendix D: PSN-1000/PSN-1000(E) Maintenance and Testing121
Appendix E: Compatible Devices Table122
Appendix F: Troubleshooting Tips123
Appendix G: Control Panel Menu124

Janus JFS-A1 - Cabinet Installation

Table of Contents