Magnescale LH71A User Manual

LH71A / LH72
(CS) i
目录
1. 使用前须知 ....................................................................... 1-1
1-1. 通用的注意事项 ................................................................................ 1-1
2. 特点 .................................................................................. 2-1
3. 各部分的名称和功能 ......................................................... 3-1
3-1. 前面板 .............................................................................................. 3-1
3-1-1. LH71A ............................................................................... 3-1
3-1-2. LH72 ................................................................................. 3-2
3-2. 后面板 .............................................................................................. 3-3
4. 连接和安装 ....................................................................... 4-1
4-1. 附件 .................................................................................................. 4-1
4-2. 安装 .................................................................................................. 4-1
4-3. 连接 .................................................................................................. 4-2
4-3-1. 可连接的长度测量元件 ..................................................... 4-2
4-3-2. 连接 .................................................................................. 4-2
5. 设定 .................................................................................. 5-1
5-1. 设定流程和设定项目 ........................................................................ 5-1
5-1-1. 从设定到开始使用的流程 .................................................. 5-1
5-1-2. 基本设定 的说明 ............................................................. 5-1
5-1-3. 详细设定 的说明 ............................................................. 5-2
5-1-4. 用于设定的键 .................................................................... 5-3
5-1-5. 设定方法 ........................................................................... 5-3
5-2. 通用用途、铣床功能的设定.............................................................. 5-4
5-2-1. 出厂后第一次接通电源时 (LH71A通用用途 / 铣床功能) ... 5-4
5-2-2. 重新设定基本设定时 (LH71A通用用途 / 铣床功能) ........... 5-5
5-2-3. 重新设定详细设定时 (LH71A通用用途 / 铣床功能) ........... 5-6
5-3. 车床功能的设定 ................................................................................ 5-7
5-3-1. 出厂后第一次接通电源时 (LH71A车床功能、LH72) ......... 5-7
5-3-2. 重新设定基本设定时 (LH71A车床功能、LH72) ................ 5-8
5-3-3. 重新设定“详细设定”时 (LH71A车床功能、LH72) ......... 5-9
5-4. 加法显示时各计数值的确认方法 .................................................... 5-10
5-5. 有关补偿 ........................................................................................ 5-11
5-5-1. 线型补偿 ......................................................................... 5-11
5-5-2. 区间误差补偿 .................................................................. 5-15
5-6. 定称 ................................................................................................ 5-18
6. 操作的开始和结束 ............................................................ 6-1
6-1. 电源 ON (接通)................................................................................. 6-1
6-2. 操作开始 .......................................................................................... 6-1
6-3. 作业中断 .......................................................................................... 6-2
6-3-1. 作业暂停 ........................................................................... 6-2
6-3-2. 作业重新开始 .................................................................... 6-2
6-4. 操作结束 (电源 OFF)........................................................................ 6-2

Magnescale LH71A Specifications

General

Brand	Magnescale
Model	LH71A
Category	Cash Counter
Language	English