TechnipFMC Sening MultiFlow - Page 300

MN F09 002 US  DOK-383E  Issue/Rev. 3.65 (02/24)
MultiFlow  Address and contact details
302
Sening® is a registered trademark of FMC Technologies
No.
Name
Seal
K
Factory
Setting
Meaning
3.1.6.0.3
Transmission delay
M
2
50ms
Interface-end telegram delay on CAN bus. (0 ..
250ms)
3.1.6.0.4
Outputs
3.1.6.0.4.1
Output1
3.1.6.0.4.1.1
Link
3.1.6.0.4.1.1.1
Output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.1.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.1.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.1.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.
3.1.6.0.4.1.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined.
3.1.6.0.4.1.2
Additional hose path
3.1.6.0.4.1.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.1.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.2
Output2
3.1.6.0.4.2.1
Link
3.1.6.0.4.2.1.1
Output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.2.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.2.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.2.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.
3.1.6.0.4.2.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined. (0, 10 ..
39)
3.1.6.0.4.2.2
Additional hose path
3.1.6.0.4.2.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.2.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.3
Output3
3.1.6.0.4.3.1
Link
3.1.6.0.4.3.1.1
Output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.3.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.3.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.3.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.
3.1.6.0.4.3.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined. (0, 10 ..
39)
3.1.6.0.4.3.2
Additional hose path
3.1.6.0.4.3.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.3.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.4
Output4
3.1.6.0.4.4.1
Link
3.1.6.0.4.4.1.1
Output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.4.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.4.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.4.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.