TechnipFMC Sening MultiFlow - Page 301

MN F09 002 US  DOK-383E  Issue/Rev. 3.65 (02/24)
MultiFlow  Address and contact details
Sening
®
is a registered trademark of FMC Technologies
303
No.
Name
Seal
K
Factory
Setting
Meaning
3.1.6.0.4.4.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined. (0, 10 ..
39)
3.1.6.0.4.4.2
Additional hose path
3.1.6.0.4.4.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.4.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.5
Output5
3.1.6.0.4.5.1
Link
3.1.6.0.4.5.1.1
Output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.5.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.5.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.5.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.
3.1.6.0.4.5.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined. (0, 10 ..
39)
3.1.6.0.4.5.2
Additional hose path
3.1.6.0.4.5.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.5.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.6
Output6
3.1.6.0.4.6.1
Link
3.1.6.0.4.6.1.1
Output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.6.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.6.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.6.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.
3.1.6.0.4.6.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined. (0, 10 ..
39)
3.1.6.0.4.6.2
Additional hose path
3.1.6.0.4.6.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.6.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.7
Output7
3.1.6.0.4.7.1
Link
3.1.6.0.4.7.1.1
output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.7.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.7.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)
3.1.6.0.4.7.1.4
Inversion
M
2
0 (no)
Status of the allocated ext. output should assume
inverted status of the reference in/output.
3.1.6.0.4.7.1.5
Product dependency
M
2
0 (no)
Up to 5 project dependencies can be defined. (0, 10 ..
39)
3.1.6.0.4.7.2
Additional hose path
3.1.6.0.4.7.2.1
Use
M
2
0 (no)
Use output to control an additional hose path.
3.1.6.0.4.7.2.2
Designation
M
2
Designation of the additional hose path
3.1.6.0.4.8
Output8
3.1.6.0.4.8.1
Link
3.1.6.0.4.8.1.1
output
M
2
0
Local reference output to be linked 1 .. 7
3.1.6.0.4.8.1.2
Input
M
2
0
Reference input to be linked 1 .. 4 (local), 5 .. 6
(external)
3.1.6.0.4.8.1.3
Delay time
M
2
0 * 0.1s
Minimum time between detected change of the
reference in/output and switching of the allocated ext.
output. (0 .. 100 * 0.1s)