Ceragon FA4800 - Page 17

FA4800 User Manual Release 1.9.40 xvi
F
IGURE 8-20 SITE CONFIGURATION - RESET TO FACTORY DEFAULTS.............................8-23
F
IGURE 8-21 ALIGNMENT TONE BUZZER STATES .......................................................8-25
F
IGURE 8-22 TELNET SESSION LOG ON ..................................................................8-26
F
IGURE 8-23 TELNET MANAGEMENT WINDOW..........................................................8-27
F
IGURE 9-1 GET DIAGNOSTICS DIALOG BOX.............................................................9-2
F
IGURE 9-2 LOOPBACK CONFIGURATION BOX .............................................................9-4
F
IGURE 9-3 LOOPBACK CONFIGURATION BOX WITH ONE SITE A PORT SELECTED.................9-4
F
IGURE 9-4 LOOPBACK OPTIONS.............................................................................9-4
F
IGURE 9-5 LOOPBACK DEFINED.............................................................................9-5
F
IGURE 9-6 SITE A PORT 2 SET TO LOOPBACK...........................................................9-5
F
IGURE 9-7 LOCAL LINE LOOPBACK.........................................................................9-6
F
IGURE 9-8 REMOTE REVERSE LOOPBACK.................................................................9-6
F
IGURE 9-9 REMOTE LINE LOOPBACK ......................................................................9-7
F
IGURE 9-10 LOCAL REVERSE LOOPBACK..................................................................9-7
F
IGURE 9-11 PREFERENCES DIALOG BOX ..................................................................9-9
F
IGURE 9-12 BASIC PERFORMANCE MONITORING REPORT ..........................................9-10
F
IGURE 9-13 A TYPICAL PERFORMANCE MONITORING REPORT BASED ON 15 MINUTE INTERVALS9-10
F
IGURE 9-14 PERFORMANCE MONITORING REPORT SHOWING THE EFFECT OF A RESET ......9-11
F
IGURE 9-15 THRESHOLD CONFIGURATION DIALOG BOX.............................................9-13
F
IGURE 9-16 EVENTS LOG DISPLAY ......................................................................9-14
F
IGURE 9-17 PREFERENCES DIALOG BOX - EVENT TAB ...............................................9-16
F
IGURE 9-18 ACTIVE ALARMS SUMMARY ................................................................9-17
F
IGURE 9-19 RECENT EVENTS - UP TO LAST 256 EVENTS AT SITE A............................9-18
F
IGURE 9-20 ADVANCED PREFERENCES ..................................................................9-18
F
IGURE 10-1 INTERFERENCE CAUSED BY COLLOCATED UNITS .......................................10-2
F
IGURE 10-2 COLLOCATED UNITS USING HUB SITE SYNCHRONIZATION (1) ....................10-2
F
IGURE 10-3 COLLOCATED UNITS USING HUB SITE SYNCHRONIZATION (2) ....................10-2
F
IGURE 10-4 HSS INTERCONNECTION UNIT............................................................10-3
F
IGURE 10-5 HSS WIRING SCHEMATIC..................................................................10-4
F
IGURE 10-6 HSS SYNC SIGNAL PATH WITH ODU 1 AS HSS MASTER...........................10-4
F
IGURE 10-7 CASCADING TWO HSS UNITS .............................................................10-5
F
IGURE 10-8 CASCADING THREE HSS UNITS...........................................................10-6
F
IGURE 10-9 ODU BEEP FOR HSS ERROR..............................................................10-7
F
IGURE 10-10 RADIO FRAME PATTERN..................................................................10-8
F
IGURE 10-11 SERVICES AND RATES - FIBEAIR 2000 100 MASTER, FIBEAIR 2000 CLIENTS10-9
F
IGURE 10-12 SERVICES AND RATES - FIBEAIR 2000 100 MASTER, FIBEAIR 2000 CLIENTS - EXTREME
ASYMMETRIC ALLOCATION
......................................................................................10-10
F
IGURE 10-13 HSS SETTINGS: LEFT - FA4800 CLIENT, RIGHT - FIBEAIR 2000 MASTER 10-12
F
IGURE 10-14 HUB SITE CONFIGURATION DIALOG - LEFT FA4800, RIGHT FIBEAIR 200010-14
F
IGURE 10-15 SITE CONFIGURATION: HSS - LEFT - FA4800 CLIENT, RIGHT - FIBEAIR 2000 MASTER
10-14
F
IGURE 10-16 HSS NOT SUPPORTED..................................................................10-15
F
IGURE 12-1 CERAGON MONITORED HOT STANDBY..................................................12-1
F
IGURE 12-2 CERAGON Y-CONNECTION PATCH PANEL...............................................12-3
F
IGURE 12-3 HOW TO CONNECT THE IDUS TO THE PATCH PANEL................................12-4
F
IGURE 12-4 SERVICES CONFIGURATION PANEL: HOT STANDBY MODE SELECTION............12-5
F
IGURE 12-5 THE PRIMARY LINK UNDER NORMAL OPERATION ......................................12-6
F
IGURE 12-6 THE SECONDARY LINK UNDER NORMAL OPERATION ..................................12-7
F
IGURE 12-7 PRIMARY LINK A FEW SECONDS BEFORE REGULAR NO-LINK DISPLAY.............12-8
F
IGURE 12-8 SECONDARY LINK OPERATING AS THE HOT STANDBY LINK.........................12-9
F
IGURE 12-9 PRIMARY LINK AFTER THE SWITCH OVER TO SECONDARY LINK (AFTER A FEW SECONDS THE
DISPLAY MOVES TO
NO-LINK DISPLAY, WITH TDM PORTS GRAYED OUT.)..........................12-11
F
IGURE 12-10 SECONDARY LINK OPERATING AFTER THE SWITCH OVER TO SECONDARY. (AFTER A FEW
MOMENTS THE
TDM ICONS BECOME GREEN.).............................................................12-12