Cisco CRS Configuration Guide

tunnel-te2 200.0.0.3 up up
tunnel-te50 200.0.0.3 up up
*tunnel-te60 200.0.0.3 up up
*tunnel-te70 200.0.0.3 up up
*tunnel-te80 200.0.0.3 up up
RP/0/RP0/CPU0:router# show mpls traffic-eng tunnels tabular
Tunnel LSP Destination Source FRR LSP Path
Name ID Address Address State State Role Prot
------------------ ------ --------------- --------------- ------- ------- ------ -----
tunnel-te0 549 200.0.0.3 200.0.0.1 up Inact Head InAct
tunnel-te1 546 200.0.0.3 200.0.0.1 up Inact Head InAct
tunnel-te2 6 200.0.0.3 200.0.0.1 up Inact Head InAct
tunnel-te50 6 200.0.0.3 200.0.0.1 up Active Head InAct
tunnel-te60 4 200.0.0.3 200.0.0.1 up Active Head InAct
tunnel-te70 4 200.0.0.3 200.0.0.1 up Active Head InAct
tunnel-te80 3 200.0.0.3 200.0.0.1 up Active Head InAct
This example shows the auto-tunnel backup details.
RP/0/RP0/CPU0:router# show mpls traffic-eng tunnels auto-tunnel backup detail
Name: tunnel-te400 Destination: 1.1.1.1 (auto-tunnel backup)
Status:
Admin: up Oper: up Path: valid Signalling: connected
path option 20, type explicit (autob_nnhop_te400) (Basis for Setup, path weight 2)
path option 10, type explicit (autob_nnhop_srlg_te400) [disabled]
G-PID: 0x0800 (derived from egress interface properties)
Bandwidth Requested: 0 kbps CT0
Creation Time: Thu Aug 16 18:30:41 2012 (00:01:28 ago)
Config Parameters:
Bandwidth: 0 kbps (CT0) Priority: 7 7 Affinity: 0x0/0xffff
Metric Type: TE (default)
Metric Type: TE (default)
Hop-limit: disabled
AutoRoute: disabled LockDown: disabled Policy class: not set
Forwarding-Adjacency: disabled
Loadshare: 0 equal loadshares
Auto-bw: disabled
Fast Reroute: Disabled, Protection Desired: None
Path Protection: Not Enabled
Soft Preemption: Disabled
Auto Backup:
Protected LSPs: 1
Protected S2L Sharing Families: 0
Protected S2L: 0
Protected i/f: Gi0/1/0/3 Protected node: 3.3.3.3
Attribute-set: ab1
Protection: NNHOP
Unused removal timeout: not running
Path Option Details:
10: Explicit Path Name: (autob_nnhop_srlg_te400)
1: exclude-srlg 34.9.0.4
2: exclude-address 34.9.0.3
3: exclude-node 3.3.3.3
20: Explicit Path Name: (autob_nnhop_te400)
1: exclude-address 34.9.0.4
2: exclude-address 34.9.0.3
3: exclude-node 3.3.3.3
SNMP Index: 221
History:
Tunnel has been up for: 00:00:34 (since Thu Aug 16 18:31:35 EST 2012)
Current LSP:
Uptime: 00:00:34 (since Thu Aug 16 18:31:35 EST 2012)
Current LSP Info:
Instance: 2, Signaling Area: OSPF 100 area 1.2.3.4
Uptime: 00:00:34 (since Thu Aug 16 18:31:35 EST 2012)
Outgoing Interface: GigabitEthernet0/1/0/2, Outgoing Label: 16000
Router-IDs: local 4.4.4.4
downstream 2.2.2.2
Soft Preemption: None
Path Info:
Cisco IOS XR MPLS Configuration Guide for the Cisco CRS Router, Release 5.1.x
358
Implementing MPLS Traffic Engineering
Configure the MPLS-TE Auto-Tunnel Backup: Example

Cisco CRS Specifications

General

Operating System	Cisco IOS XR
Product Type	Core Router
Form Factor	Modular Chassis
Dimensions	Varies by chassis type
Weight	Varies by chassis type
Architecture	Distributed
Switch Fabric	Multi-stage
Interface Support	Ethernet, SONET/SDH, OTN
Interfaces/Ports	Varies by line card
Port Density	Varies by line card
Routing Protocol	BGP, IS-IS, OSPF, MPLS
Management	CLI, SNMP
Power Supply	Redundant, hot-swappable
Cooling	Redundant, Hot-swappable Fan Trays
Supported Protocols	IPv4, IPv6, MPLS
Management Interfaces	Ethernet, console
Security Features	ACLs