Dekema AUSTROMAT 674 baSiC

To Next Page

To Previous Page

9. Safety data sheets AUSTROMAT

664 iSiC

/ 674 baSiC

136 Operating Instructions (Version 03/2018)

Main Page

Table of Contents3
Usage, Data8
Introduction8
Proper Use9
Scope of Delivery10
Name Plate11
Technical Data12
Ambient Conditions14
Safety15
This Section Must be Read15
Organization of the Safety Instructions16
General Safety Regulations17
Operating Instructions17
Operation18
Maintenance and Service19
Disposal19
Risks20
Access Rights22
Stop Function22
Design and Functionality23
Front of System23
Touchscreen and Function Keys24
Touchscreen24
Function Keys25
Rear of Device26
Start-Up27
Unpacking and Setting up27
Requirements at the Setup Site28
Assembling the Heating Elements29
First Startup30
Procedure30
Installation Assistant (Country-Specific)31
Connect the Firing Oven to the Network (Optional)32
Determine the IP Address32
Setting up the Operation of the Firing Furnace Using a Browser33
Setting up the Operation of the Firing Furnace Using a VNC Program34
Setting up a Permanent IP Address for the Firing Furnace35
Specify Authorizations36
Access through a Browser or a VNC Program36
Connect the Firing Furnace to an Individual PC (Optional)37
Setting up the Operation of the Firing Furnace Using a Browser37
Operating the Firing Furnace Using a VNC Program38
Access through a Browser or a VNC Program39
User Interface40
Basic Information40
Terms40
Screen Elements41
Numeric Screen Keyboard42
Alphanumeric Keyboard Window43
Keyboard Window for the Classic Editor44
Screen Display45
Program Manager46
Icon Manager49
Program Display52
Classic Programs52
Pictures54
Program Sequence56
Program Editor58
Editing Classic Programs58
Creating a New Program60
Programming Suggestions60
Setup Menu61
System Control Functions64
Units64
Language65
Date/Time66
Screen Settings67
Network (Optional)68
General Code69
System Setting Functions71
Furnace ID71
Acoustic Signal73
Heating Settings74
Lift Settings75
Maintenance Programs76
Drying76
Check Program77
Oxidation78
Temperature Calibration79
Data Recording and Transfer80
Printer80
Quality Management (Optional)81
Diagnostic Data82
Login Data (Optional)83
Backup / Recovery84
FTP Server Login (Optional)86
Operation88
Turning on and off88
Mounting and Removing a Firing Object89
Select Programs and Start Them91
With the Touchscreen91
With Web Interface (Optional)91
With VNC Program (Optional)92
Operating Layout for the Menu Control93
Program End94
Some Practical Tips95
General Operation of the Furnace95
Heating Element95
Thermocouple Temperature Calibration95
Programming and Program Steps95
Firing Programs96
Backing up and Restoring Firing Programs97
Backup with a USB Stick97
Restore Data with a USB Stick99
Backing up and Restoring Data101
Loading and Saving Sets102
Download Set from the Internal Memory102
Load Set from a USB Stick102
Load a Set from an FTP Server (Optional)103
Download Set from the Internet (Optional)103
Internally Save Set105
Saving a Set on a USB Stick105
Save a Set on an FTP Server (Optional)105
Access the Firing Furnace Via FTP (Optional)106
Quality Assurance (Optional)108
QM Logs108
X-Dream (Optional)109
OPC (Optional)109
After a Power Failure110
Maintenance and Service111
Care111
Calibrate Temperature112
Check Program115
Change the Heating Element116
Software Update116
Enable Software Options117
Service and Transport119
Storage and Disposal120
Storage120
Disposal121
Personnel Qualifications121
Legal Guidelines121
Disposal: Electrical and Electronic Materials122
Disposal: Other Assemblies and Components122
Safety Data Sheets123
Altraform" Safety Data Sheet124
Kerform" Safety Data Sheet130
Isolrath" (Super-Isol) Safety Data Sheet142
Index145

Dekema AUSTROMAT 674 baSiC - Page 136

Table of Contents

Related product manuals