Entron EN1000 series User Manual

Page 8 • 700120S • ENTRON Controls, LLC.
FIGURE 8-1 JUMPER SETTING: PRIMARY CURRENT TRANSFORMER ................................ 98
FIGURE 8-2 JUMPER SETTING: SECONDARY ROGOWSKI COIL ........................................... 98
FIGURE 8-3 JUMPER SETTINGS .............................................................................................. 104
FIGURE 9-1 SPOT WITH REPEAT MODE ................................................................................. 106
FIGURE 9-2 PULSATION WITH SUCCESSIVE MODE ............................................................. 106
FIGURE 9-3 QUENCH-TEMPER WITH CHAINED MODE ........................................................ 107
FIGURE 9-4 UPSLOPE AND DOWNSLOPE WITH CHAINED MODE ...................................... 107
FIGURE 9-5 BUTT WELD WITH CHAINED MODE ................................................................... 108
FIGURE 9-6 FORGE DELAY WITH CHAINED MODE ............................................................... 109
FIGURE 9-7 CONTINUOUS SEAM MODE ................................................................................ 110
FIGURE 9-8 INTERMITTENT SEAM MODE .............................................................................. 110
FIGURE 9-9 NON-BEAT SEAM MODE ...................................................................................... 111
FIGURE 9-10 USING TWO STAGE INITIATION IN BRAZING MODE ......................................... 112
FIGURE 9-11 SQUEEZE DELAY OPERATION ............................................................................ 113
FIGURE 9-12 MOMENTARY RETRACTION CONNECTIONS .................................................... 115
FIGURE 9-13 MAINTAINED CLOSURE RETRACTION CONNECTIONS ................................... 116
FIGURE 9-14 AIR OVER OIL RETRACTION CONNECTIONS.................................................... 118
FIGURE 9-15 AIR OVER OIL RETRACTION TIMING DIAGRAMS ............................................. 121
FIGURE 9-16 SCHEDULE SELECT ............................................................................................. 122
FIGURE 9-17 PROCESS OUTPUT
2626
2626
26 WIRING ........................................................................... 123
TABLES
TABLE 2-1 SLOPE MODES ....................................................................................................... 15
TABLE 2-2 CYCLE MODES ....................................................................................................... 15
TABLE 2-3 VALVE CODES ......................................................................................................... 16
TABLE 3-1 EXTERNAL SCR CONTACTOR CONNECTIONS ................................................... 23
TABLE 5-1 EXTERNAL SCHEDULE SELECT WITH FS7 AND FS11 ....................................... 51
TABLE 5-2 S49 EXTERNAL SCHEDULE SELECT.................................................................... 54
TABLE 5-3 STEPPER SELECTION USING SS1, SS2, SS4, SS8 ............................................. 55
TABLE 5-4 ORIGINAL AVC VALUES ......................................................................................... 57
TABLE 5-5 AVC PARAMETER VALUES .................................................................................... 57
TABLE 5-6 PROCESS OUTPUT CODES AND DESCRIPTIONS .............................................. 62
TABLE 5-7 CONSTANT CURRENT MODES ............................................................................. 71
TABLE 5-8 MAXIMUM AND MINIMUM VALUES FOR
rr
rr
r
.A..A.
.A..A.
.A. ......................................................... 72
TABLE 6-1 VALVE CODES ......................................................................................................... 83
TABLE 6-2 VALVE MODES AND VALVE OUTPUTS .................................................................. 86
TABLE 7-1 SCHEDULE MAP USED FOR STEPPER PROGRAMMING ................................... 88
TABLE 7-2 STEPPER CODES ................................................................................................... 89
TABLE 7-3 STEPPER SELECTION USING FS7 AND FS11 ..................................................... 92
TABLE 7-4 STEPPER SELECTION USING SS1, SS2, SS4, SS8 ............................................. 92
TABLE 7-5 PROGRAMMING FOR STEPPER MODE
0202
0202
02 ........................................................... 94
TABLE 8-1 OPERATING RANGES FOR PRESET-RANGE SELECTION WITH
ROGOWSKI COIL .................................................................................................... 99
TABLE 9-1 EXTERNAL SCHEDULE SELECT WITH FS7 AND FS11 ..................................... 122
TABLE OF CONTENTS (cont.)
FIGURES (cont.)

Entron EN1000 series Specifications

General

Brand	Entron
Model	EN1000 series
Category	Controller
Language	English