Entron EN1000 series

ENTRON Controls, LLC. • 700120S • Page 7
FIGURES
FIGURE 1-1 EN1000/EN1001 SYSTEM......................................................................................... 9
FIGURE 1-2 CONTROL PANEL LAYOUT .................................................................................... 11
FIGURE 3-1 INSTALLATION AND MOUNTING DIAGRAMS FOR STYLE “S” CABINET ............ 17
FIGURE 3-2 INSTALLATION OF STYLE “E” CABINET – 300A & 1200A CONTACTOR ............. 18
FIGURE 3-3 INSTALLATION OF STYLE “E” CABINET – 1800/2200/3200A CONTACTOR ........ 18
FIGURE 3-4 MECHANICAL MOUNTING DIAGRAM FOR “E” CABINET .................................... 18
FIGURE 3-5 INSTALLATION OF STYLE “T/D” & “L” CABINETS – 1200A CONTACTOR ........... 19
FIGURE 3-6 INSTALLATION OF STYLE “T/D” & “L” CABINETS –
1800/2200/3200A CONTACTOR.............................................................................. 19
FIGURE 3-7 MECHANICAL MOUNTING DIAGRAM FOR “T/D” AND “L” CABINETS ................. 19
FIGURE 3-8 INSTALLATION DIAGRAM FOR STYLE “C” CABINET ........................................... 20
FIGURE 3-9 MOUNTING DIAGRAMS FOR STYLE “C” CABINET .............................................. 20
FIGURE 3-10 INSTALLATION AND MOUNTING DIAGRAMS FOR 11x11 FLAT PLATE ............... 21
FIGURE 3-11 INSTALLATION AND MOUNTING DIAGRAMS FOR 21x21 FLAT PLATE .............. 21
FIGURE 3-12 INSTALLATION AND MOUNTING DIAGRAMS FOR 13x19 FLAT PLATE .............. 22
FIGURE 3-13 INSTALLATION AND MOUNTING DIAGRAMS FOR IMU ....................................... 22
FIGURE 3-14 EXTERNAL SCR CONTACTOR CONNECTIONS ................................................... 24
FIGURE 3-15 DEMAND CURRENT VS. PERCENT DUTY CYCLE ............................................... 26
FIGURE 4-1 VOLTAGE OPERATION JUMPERS SETTINGS ...................................................... 28
FIGURE 4-2 VALVE TRANSFORMER JUMPERS SETTINGS .................................................... 29
FIGURE 4-3 WARNING, DANGER AND CAUTION LABELS ....................................................... 30
FIGURE 4-4 TERMINAL STRIP/FIRING BOARD ......................................................................... 31
FIGURE 4-5 COMPONENT PLACEMENT ON NEW TERMINAL STRIP/FIRING BOARD .......... 32
FIGURE 4-6 TERMINAL STRIP FOR “T/D” CABINET ................................................................. 35
FIGURE 4-7 INITIATION INPUTS ON TERMINAL STRIP TS1 .................................................... 36
FIGURE 4-8 OTHER INPUTS ON TERMINAL STRIP TS1 .......................................................... 37
FIGURE 4-9 FLASHING
1414
1414
14 OR
3232
3232
32 ERRORS ................................................................................. 38
FIGURE 4-10 WRONG ROUTING OF LOW AND HIGH VOLTAGE WIRES .................................. 39
FIGURE 4-11 BETTER ROUTING OF LOW AND HIGH VOLTAGE WIRES .................................. 39
FIGURE 4-12 RECOMMENDED ROUTING OF LOW AND HIGH VOLTAGE WIRES ................... 39
FIGURE 4-13 ISOLATION CIRCUIT BLOCK DIAGRAM ................................................................ 40
FIGURE 5-1 FOUR-DIGIT DATA DISPLAY ................................................................................... 42
FIGURE 5-2 COPY SCHEDULE UP BY 1 .................................................................................... 45
FIGURE 5-3 COPY SCHEDULE UP BY 10 .................................................................................. 45
FIGURE 5-4 CLEAR SCHEDULE DATA ....................................................................................... 45
FIGURE 5-5 SELECTING FUNCTIONS ....................................................................................... 46
FIGURE 5-6 EXTENDED FUNCTIONS MODE ............................................................................ 46
FIGURE 5-7 VIEWING EXTENDED FUNCTIONS ....................................................................... 46
FIGURE 5-8 DUAL TWO-STAGE FOOT SWITCH INITIATION .................................................... 52
FIGURE 5-9 MULTIPLE TWO-STAGE FOOT SWITCH INITIATION ............................................ 52
FIGURE 5-12 SWITCH CLOSURE CONNECTIONS ..................................................................... 54
FIGURE 5-13 MULTIPLE PILOT SWITCH CONNECTIONS .......................................................... 55
FIGURE 5-14 CLEAR SCHEDULE DATA ....................................................................................... 59
FIGURE 5-15 BACK-STEP SEQUENCE EXAMPLE ...................................................................... 60
FIGURE 5-16 USING LIGHT CURTAIN .......................................................................................... 67
FIGURE 6-1 NON-REPEAT SEQUENCE ..................................................................................... 78
FIGURE 6-2 REPEAT SEQUENCE .............................................................................................. 79
FIGURE 6-3 CHAINED SEQUENCE ............................................................................................ 80
FIGURE 7-1 STEPPER ENABLING ............................................................................................. 87
FIGURE 7-2 SELECT WELD/HEAT .............................................................................................. 89
FIGURE 7-3 PROGRAM WELD COUNT ...................................................................................... 89
FIGURE 7-4 PROGRAM LAST STEP ........................................................................................... 90
FIGURE 7-5 PROGRAM LAST COUNT ....................................................................................... 90
FIGURE 7-6 ALGORITHM ............................................................................................................ 93
TABLE OF CONTENTS (cont.)