evertz 7700 - Page 5

7700 Multiframe Manual
7725DSK-LG / 7725DSK-LG-HD HD/SD Logo Inserter & Media Keyer
TABLE OF CONTENTS Revision 1.4 Page v
4.6.5.4. Displaying the Ethernet Hardware Address ............................................ 4-16
4.6.6. Displaying SNMP Trap Destination........................................................................ 4-16
4.6.7. Displaying AFD Logo Trigger................................................................................. 4-16
4.6.8. Setting the Serial Protocol for COM Ports D and E ............................................... 4-16
4.6.9. Setting the Genlock Status .................................................................................... 4-17
4.6.10. Protecting Line 21 Captions................................................................................... 4-18
4.6.11. Setting the Unit Name............................................................................................ 4-18
4.6.12. Setting the Up Down Timer.................................................................................... 4-18
4.6.13. Automation Debug Functions................................................................................. 4-19
4.7. FILE MANAGEMENT CONFIGURATION ITEMS............................................................. 4-19
4.7.1. Selecting the Source Media ................................................................................... 4-20
4.7.2. Selecting the Media File Name .............................................................................. 4-20
4.7.3. Selecting the Destination Media ............................................................................ 4-20
4.7.4. Deleting a File ........................................................................................................ 4-20
4.7.5. Erasing all the Files from a Media Disk.................................................................. 4-20
4.8. MATTE CONFIGURATION ITEMS ................................................................................... 4-21
4.8.1. Turning the Matte On and Off ................................................................................ 4-21
4.8.2. Setting the Matte Aspect Ratio .............................................................................. 4-21
4.8.3. Setting a User Defined Matte Aspect Ratio ........................................................... 4-22
4.9. DOWNSTREAM KEYER CONFIGURATION ITEMS........................................................ 4-22
4.9.1. Setting the Downstream Key Type ........................................................................ 4-22
4.9.2. Setting the Downstream Key Object Transparency ............................................... 4-23
4.9.3. Setting the Downstream Key Object Offset ........................................................... 4-23
4.9.4. Setting the Downstream Self Key Threshold ......................................................... 4-23
4.9.5. Allowing Automation to Control the Media Layer ................................................... 4-23
4.10. TRANSITION CONFIGURATION ITEMS.......................................................................... 4-24
4.10.1. Setting the Transition Type .................................................................................... 4-24
4.10.2. Setting the Transition Rate .................................................................................... 4-25
4.10.3. Setting the Transition Swap Mode ......................................................................... 4-25
4.10.4. Pausing a Transition .............................................................................................. 4-25
4.10.5. Setting Program Bus Change ................................................................................ 4-25
4.11. PRESET CONFIGURATION ITEMS ................................................................................. 4-26
4.11.1. Configuring the GPI Inputs..................................................................................... 4-26
4.11.1.1. Selecting One of the GPI Inputs to Configure ......................................... 4-27
4.11.1.2. Configuring the GPI Actions.................................................................... 4-27
4.11.2. Configuring the GPO Outputs ................................................................................ 4-29
4.11.3. Recalling a User Preset ......................................................................................... 4-30
4.11.4. Storing a User Preset............................................................................................. 4-30
4.11.5. Exporting a User Preset......................................................................................... 4-30
4.11.6. Selecting the Source of the Preset Settings .......................................................... 4-30
4.12. TEMPERATURE CONFIGURATION ITEMS .................................................................... 4-31
4.12.1. Setting the Temperature Source............................................................................ 4-31
4.12.2. Setting the Temperature Format............................................................................ 4-31
4.12.3. Setting the Static Temperature .............................................................................. 4-32
4.12.4. Temperature Read Loss ........................................................................................ 4-32
4.13. EAS CONFIGURATION ITEMS (+E OPTIONED UNITS ONLY)...................................... 4-32
4.13.1. Setting the EAS Display Type................................................................................ 4-33
4.13.2. Setting the Vertical Position of EAS Crawl Display................................................ 4-33