Fujitsu PRIMERGY TX1310 M3 Upgrade And Maintenance Manual

202 Upgrade and Maintenance Manual TX1310 M3
System board and components
Ê Remove the protective cover from the CPU socket of the new system board,
see section "Removing the protective cover" on page 151.
Ê Remove the CPU from the defective system board, see section "Removing
the CPU" on page 135.
Ê Confirm that the CPU model number printed on the top of the CPU fits with
the requirements.
Ê Install the CPU on the new system board, see section "Installing the CPU"
on page 138.
Ê Fit the protective plastic cover of the new system board onto the socket of
the defective system board which will to be returned.
I Returned system boards without this cover will probably have to be
scrapped.
15.4.4 Concluding steps
Ê Connect all cables to the system board. For the cable plans, please refer to
section "Cabling plans" on page 206.
Ê If applicable, "Installing the TPM" on page 186.
Ê Install the memory modules, see section "Installing a memory module" on
page 124.
I Make sure that you reinstall each memory module in the slot it was
located before the replacement.
Ê Install the heat sink, see section "Installing the heat sink" on page 143.
Ê Install all expansion cards, see section "Expansion cards" on page 113.
I Make sure that you reinstall each card in the slot it was located before
the replacement.
Ê Install the air deflector, see section "Installing the air deflector" on page 59.
Ê "Reassembling" on page 51
Ê Connect all external cables.
Ê "Connecting the power cord" on page 56

Fujitsu PRIMERGY TX1310 M3 Specifications

General

Processor cache	8 MB
Processor cores	4
Processor model	E3-1225V6
System bus rate	8 GT/s
Motherboard chipset	Intel® C236
Processor frequency	3.3 GHz
Processor cache type	Smart Cache
Processor lithography	14 nm
Processor boost frequency	3.7 GHz
Processor operating modes	64-bit
Number of processors installed	1
ECC	Yes
Internal memory	8 GB
Memory clock speed	2400 MHz
Internal memory type	DDR4-SDRAM
Maximum internal memory	64 GB
HDD size	3.5 \
HDD speed	7200 RPM
RAID levels	0, 1, 10
HDD capacity	1000 GB
HDD interface	Serial ATA III
Optical drive type	DVD-RW
Total storage capacity	2000 GB
Maximum storage capacity	- TB
Number of HDDs installed	2
On-board graphics card model	Intel® HD Graphics 630
LAN controller	Intel® I219
Cabling technology	10/100/1000Base-T(X)
Ethernet interface type	Gigabit Ethernet
Serial ports quantity	-
USB 2.0 ports quantity	3
VGA (D-Sub) ports quantity	0
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	6
Chassis type	Tower
Compatible operating systems	Microsoft Hyper-V Server 2012 R2 Microsoft Hyper-V Server 2016 Microsoft Windows Server 2012 R2 Datacenter Microsoft Windows Server 2016 Datacenter Microsoft Windows Server 2012 R2 Standard Microsoft Windows Server 2016 Standard Microsoft Windows Server 2012 R2 Essentials Microsoft Windows Server 2016 Essentials Microsoft Windows Server 2012 R2 Foundation Microsoft Windows Storage Server 2012 R2 Standard Microsoft Windows Storage Server 2016 Standard Microsoft Hyper-V Server 2012 Microsoft Windows Server 2012 Datacenter Microsoft Windows Server 2012 Standard Microsoft Windows Server 2012 Essentials Microsoft Windows Server 2012 Foundation SUSE Linux Enterprise Server 12 Red Hat Enterprise Linux 7
Power supply	250 W
Power supply input frequency	50 - 60 Hz
Redundant power supply (RPS) support	No
Operating temperature (T-T)	10 - 35 °C
Certification	CB, RoHS, WEEE, GS, CE, CSA us, ULc/us, FCC Class A, VCCI:V3 Class A + JIS 61000-3-2, KC, CCC, C-Tick (AS / NZS CISPR 22 Class A)
Sustainability certificates	EPEAT Gold

Weight and Dimensions

Depth	305 mm
Width	180 mm
Height	375 mm
Weight	14000 g