EasyManuals Logo

Fujitsu PRIMERGY TX1310 M3 Upgrade And Maintenance Manual

Fujitsu PRIMERGY TX1310 M3
234 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #70 background imageLoading...
Page #70 background image
70 Upgrade and Maintenance Manual TX1310 M3
Basic software procedures
Ê For the changes to take effect, you need to reboot the network by entering
the following command:
# service network restart
I If the system board or network controller offers multiple LAN ports, it is
necessary to update the remaining ifcfg-eth<x> definition files
accordingly.
Ê Update the NIC configuration file to reflect the new card sequence and MAC
address.
5.2.8 Resuming BitLocker functionality
If BitLocker Drive Encryption has been suspended for maintenance purposes
(see section "Suspending BitLocker functionality" on page 61), it has to be re-
enabled to complete the service task.
I If BitLocker Drive Encryption has been suspended prior to replacing
components you won't be asked for a recovery key when rebooting the
server after the maintenance task. However, if BitLocker functionality has
not been suspended, Windows will enter recovery mode and ask you to
input recovery key for further booting.
Ê In this case, ask the system administrator to enter the recovery key in
order to boot the operating system.
Ê Ask the system administrator to enable the previously suspended BitLocker-
protection on the system volume, using the BitLocker Drive Encryption control
panel item:
For Windows Server 2008:
Ê Click Start - Control Panel - Security, - BitLocker Drive Encryption to open
the BitLocker Drive Encryption.
Ê Select the system volume, and click Turn On BitLocker.
For Windows Server 2008 R2 and above:
Ê Click Start - Control Panel - System and Security - BitLocker Drive Encryption
to open the BitLocker Drive Encryption.
Ê Select the system volume, and click Resume Protection.

Table of Contents

Other manuals for Fujitsu PRIMERGY TX1310 M3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY TX1310 M3 and is the answer not in the manual?

Fujitsu PRIMERGY TX1310 M3 Specifications

General IconGeneral
Processor cache8 MB
Processor cores4
Processor modelE3-1225V6
System bus rate8 GT/s
Motherboard chipsetIntel® C236
Processor frequency3.3 GHz
Processor cache typeSmart Cache
Processor lithography14 nm
Processor boost frequency3.7 GHz
Processor operating modes64-bit
Number of processors installed1
ECCYes
Internal memory8 GB
Memory clock speed2400 MHz
Internal memory typeDDR4-SDRAM
Maximum internal memory64 GB
HDD size3.5 \
HDD speed7200 RPM
RAID levels0, 1, 10
HDD capacity1000 GB
HDD interfaceSerial ATA III
Optical drive typeDVD-RW
Total storage capacity2000 GB
Maximum storage capacity- TB
Number of HDDs installed2
On-board graphics card modelIntel® HD Graphics 630
LAN controllerIntel® I219
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeGigabit Ethernet
Serial ports quantity-
USB 2.0 ports quantity3
VGA (D-Sub) ports quantity0
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity6
Chassis typeTower
Compatible operating systemsMicrosoft Hyper-V Server 2012 R2 Microsoft Hyper-V Server 2016 Microsoft Windows Server 2012 R2 Datacenter Microsoft Windows Server 2016 Datacenter Microsoft Windows Server 2012 R2 Standard Microsoft Windows Server 2016 Standard Microsoft Windows Server 2012 R2 Essentials Microsoft Windows Server 2016 Essentials Microsoft Windows Server 2012 R2 Foundation Microsoft Windows Storage Server 2012 R2 Standard Microsoft Windows Storage Server 2016 Standard Microsoft Hyper-V Server 2012 Microsoft Windows Server 2012 Datacenter Microsoft Windows Server 2012 Standard Microsoft Windows Server 2012 Essentials Microsoft Windows Server 2012 Foundation SUSE Linux Enterprise Server 12 Red Hat Enterprise Linux 7
Power supply250 W
Power supply input frequency50 - 60 Hz
Redundant power supply (RPS) supportNo
Operating temperature (T-T)10 - 35 °C
CertificationCB, RoHS, WEEE, GS, CE, CSA us, ULc/us, FCC Class A, VCCI:V3 Class A + JIS 61000-3-2, KC, CCC, C-Tick (AS / NZS CISPR 22 Class A)
Sustainability certificatesEPEAT Gold
Weight and Dimensions IconWeight and Dimensions
Depth305 mm
Width180 mm
Height375 mm
Weight14000 g

Related product manuals