EasyManua.ls Logo

GE Brivo OEC 715 - Page 67

GE Brivo OEC 715
551 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
System Overview
2-13
Power on/off button interface
The voltages applied to the power on/off button are listed as follows.
Name
Description
Pin
Attribution
Scale
Comment
SYS_ONOFF_CTRL_1
The button switch
on/off terminal
PJ5-1
Power
0/+12VDC
SYS_ONOFF_CTRL_2
PJ5-2
Power
0/+12VDC
BUTTON_LED_+12V
The button
indicator
PJ5-3
Power
0/+12VDC
BUTTON_LED_GND
PJ5-4
power
0
CMPTR_+12V interface
The +12VDC power from computer are listed as follows.
Name
Description
Pin
Attribution
Scale
Comment
+12V_CMPTR
+12VDC Power from computer
PJ4-1
power
0/+12VDC
GND_CMPTR
GND Reference point
PJ4-2
power
0
Interlock interface
The interlock signals for cable &board are listed as follows.
Name
Description
Pin
Attribution
Scale
Comment
INTERLOCK_CABLE
Interlock cable signal
PJ3-3
signal
0/+12VDC
INTERLOCK_COM
GND Reference point
PJ3-2
signal
0/+12VDC
INTERLOCK_BOARD
Interlock board signal
PJ3-1
signal
0/+12VDC
PC power on/off switch interface
The switch on/off signal for PC are listed as follows.
Name
Description
Pin
Attribution
Scale
Comment
CMPTR_CTRL_1
PC ON/OFF Control
PJ10-1
signal
CMPTR_CTRL_2
PJ10-2
signal
JTAG interface
Name
Description
Pin
Attribution
Scale
Comment
TCLK
JTAG input pin
PJ9-1
signal
0/+3.3V
GND
GND
PJ9-2,10
power
0/+3.3V
TDO
JTAG input pin
PJ9-3
signal
0/+3.3V
VCC_+3.3V
+3.3VDC power
PJ9-4
power
0/+3.3V
TMS
JTAG input pin
PJ9-5
signal
0/+3.3V
TDI
JTAG input pin
PJ9-9
signal
0/+3.3V
System Interface Board interface
The signals to SIB are listed as follows.
Name
Description
Pin
Attribution
Scale
Comment
SYS_PWR_REQ
system switch on/off signal
PJ8-1
digital
0/+12V (>6V=High)
GND
GND
PJ8-2
GND
0V
MAINS_LOST_ERR
status of Mainframe Power
PJ8-3
digital
0/+12V (>6V=High)
SEC_OVR_VLTGE_ERR
transformer secondary over
voltage signal
PJ8-4 digital 0/+12V (>6V=High)
SEC_UDR_VLTGE_ERR
transformer secondary
under voltage signal
PJ8-5 digital 0/+12V (>6V=High)
12V_ERR
+12V voltage from
computer fault signal
PJ8-6 digital 0/+12V (>6V=High)
RDY_ERR
WKS boot up ready fault
signal
PJ8-7 digital 0/+12V (>6V=High)

Table of Contents

Other manuals for GE Brivo OEC 715

Related product manuals