IBM 6400 Setup Guide

D–5
Appendix D. Attaching Host Systems to a Coax/Twinax Printer
Attaching Printer to Remote Control Unit with Twinax Interface
AS/400’s auto configuration program does not support remote attached
printers. You must manually configure this printer as a remote printer
attached to a 5294, 5394, or 5494 Remote Control Unit. Use the following
parameters when configuring this printer as a remote printer on AS/400:
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Parameter Description
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Parameter
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Parameter Setting
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Device description
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
DEVD
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Workstation printer name
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Device class
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
DEVCLS
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
*RMT
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Device type
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
TYPE
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
*IPDS (When printer is set to 4234–12 mode.)
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Device type
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
TYPE
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
4234 (When printer is set to 4234–2 mode.)
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Device model
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
MODEL
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
0000 (00 if IPDS (4234–12) and 02 if SCS (4234–2))
ÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁ
Advanced Function
ÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁ
AFP
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
*NO (See Note)
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Location Address
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
LOCADR
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
xx
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Online at IPL
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ONLINE
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
*YES
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Attached controller
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
CTL
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Remote controller name
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Font identifier
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
FONT
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
yyy (Default font identifier)
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Form feed
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
FORMFEED
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
* Cont
NOTE: AFP *Yes can be specified if the level of OS/400 supports the
printer as an AFP printer and PSF/400 is installed.
Attaching Printer to an IBM System/36 with Twinax Interface
DANGER:
<4> Do not connect or disconnect any communication port, teleport,
attachment connector, or power cord during an electrical storm.
<5> Power off the print and disconnect the power cord before connecting or
disconnecting communication port, teleport, or attachment cable
connector.
This section contains instructions for attaching your printer to an IBM
System/36. For additional information not found here, see your System/36
documentation.
To connect your printer to a System/36, follow these steps:

IBM 6400 Specifications

General

Brand	IBM
Model	6400
Category	Printer
Language	English