Keithley 2700 User Manual

13-4 SCPI Signal Oriented Commands Model 2700 Multimeter/Switch System User’s Manual
CONFigure:<function> [<rang>], [<res>], [<clist>]
CONFigure:VOLTage[:DC] [<rang>], [<res>], [<clist>] Configure DCV
CONFigure:VOLTage:AC [<rang>], [<res>], [<clist>] Configure ACV
CONFigure:CURRent[:DC] [<rang>], [<res>], [<clist>] Configure DCI
CONFigure:CURRent:AC [<rang>], [<res>], [<clist>] Configure ACI
CONFigure:RESistance [<rang>], [<res>], [<clist>] Configure Ω2
CONFigure:FRESistance [<rang>], [<res>], [<clist>] Configure Ω4
CONFigure:FREQuency [<rang>], [<res>], [<clist>] Configure FREQ
CONFigure:PERiod [<rang>], [<res>], [<clist>] Configure PERIOD
CONFigure:TEMPerature [<clist>] Configure TEMP
CONFigure:CONTinuity [<clist>] Configure CONT
Parameters <rang> = Range parameter for the specified function. For example, for
DCV, range parameter value 10 selects the 10V range. See
the “NOTES” that follow Table 13-1 for additional information.
<res> = 0.1 i.e., 100.0 V (3H digits)
0.01 i.e., 10.00 V (3H digits)
0.001 i.e., 1.000 V (3H digits)
0.0001 i.e., 1.0000 V (4H digits)
0.00001 i.e., 1.00000 V (5H digits)
0.000001 i.e., 1.000000 V (6H digits)
The resolution of the <res> parameter value and the selected range
sets the number of display digits. As shown above, with the 100V
range selected and <res> = 0.1, a 100V reading will be displayed
as 100.0 V (3H digits).
The display will default to 3H digits when using parameter values
that attempt to set the display below 3H digits. For example, a 10V
reading using <res> = 0.1 for the 10V range is displayed as 10.00
V, not 10.0 V.
A command using parameter values that attempt to set the
display above 7H digits is ignored, and generates error -221
(settings conflict error).
The <res> parameter is ignored when a <clist> is included in
the command string. Resolution for the scanlist channel(s) is
determined by the present setting for the specified function and
by the present resolution setting for the specified function.
See the “NOTES” that follow Table 13-1 for additional
information.
<clist> = Channel(s) in the scanlist to be configured. When the channel
list parameter (<clist>) is included, the present instrument
settings are not affected. Instead, the channel(s) in the <clist>
for the specified function is configured. See the “NOTES” that
follow
Table 13-1 for additional information.

Keithley 2700 Specifications

General

Type	Digital Multimeter
Measurement Functions	DC Voltage, AC Voltage, DC Current, AC Current, Resistance, Frequency, Temperature
DC Voltage Range	100 mV to 1000 V
AC Voltage Range	100 mV to 750 V
Frequency Range	3 Hz to 500 kHz
Temperature Range	-200°C to +1372°C
Display	Vacuum Fluorescent Display
Connectivity	IEEE-488, RS-232
Channels	10
Power Supply	100V to 240V AC, 45Hz to 66Hz
DC Current Range	10 µA to 3 A
AC Current Range	10 µA to 3 A
Temperature Measurement	Thermocouple, RTD