I-2 Finisher Service Manual
4024-XXX
287.05 sensor (upper media exit) static jam A
2-51
287.06 sensor (upper media exit) static jam B 2-52
287.07sensor (upper media exit) static jam C 2-53
288.00 sensor (diverter gate) on jam 2-54
288.01 sensor (diverter gate) static jam (to top bin) A
2-57
288.02 sensor (diverter gate) static jam (to top bin) B
2-58
288.03 sensor (diverter gate) static jam (to top bin) C
2-59
288.04 sensor (diverter gate) static jam (to stacker bin) A
2-60
288.05 sensor (diverter gate) static jam (to stacker bin) B
2-61
288.06 sensor (diverter gate) static jam (to stacker bin) C
2-62
980.02 finisher communication failure 2-63
981.00 stacker bin fail 2-63
981.01 stacker bin upper limit failure 2-65
981.02 stacker bin lower limit failure 2-66
982.00 sensor (front tamper HP) on failure 2-68
982.01 sensor (front tamper HP) off failure 2-69
983.00 sensor (rear tamper HP) on failure 2-70
983.01 sensor (rear tamper HP) off failure 2-71
984.00 sensor (punch unit HP) on failure 2-72
984.01 sensor (punch unit HP) off failure 2-74
985.00 sensor (punch carriage shift HP) on failure 2-75
985.01 sensor (punch carriage shift HP) off failure 2-76
986.00 sensor (media eject clamp HP) on failure 2-77
986.01 sensor (media eject clamp HP) off failure 2-78
987.00 sensor (media eject shaft HP) on failure 2-79
988.00 sensor (punch unit side reg) on failure 2-82
988.01 sensor (media eject shaft HP) off failure 2-80
988.01sensor (punch unit side reg) off failure 2-83
989.00 stapler unit failure 2-85
990.00 sensor (stapler carriage HP) on failure 2-85
990.01 sensor (stapler carriage HP) off failure 2-86
995.00 finisher NVRAM R/W failure 2-87
996.00 finisher type failure 2-87
999.00 finisher engine/RIP functional failure 2-88
error messages
bridge unit top cover open
2-88
bridge unit top door open 2-91
finisher eject cover open 2-91
finisher front door open 2-90
finisher upper media bin full 2-91
no punch waste box 2-92
punch waste box full 2-93
stacker lower safety failure 2-97
stacker media bin full (mix size) 2-94
stacker media bin full (no mix) 2-96
stacker set over count failure 2-99
staple cartridge empty 2-99
ESD-sensitive parts 4-1
F
finisher
removal
4-4
finisher controller card assembly 4-118
FINISHER TESTS
Feed Tests
3-2
Hole Punch Test 3-2
Sensor Test 3-2
Bin Level
Fin upper bin full
3-3
Stacker bin level encod 3-3
Stacker bin level1 3-3
Stacker bin level2 3-3
Stacker bin no media 3-3
Stacker bin upper limit 3-3
Cover and Door
Cover F bridge top
3-3
Door G fin front 3-3
Surface H fin eject 3-3
Media Path
Bridge media ent
3-3
Bridge media exit 3-3
Buffer path 3-3
Compiler media in 3-3
Fin media enter 3-3
Fuser exit 3-3
Lower media exit 3-3
Upper media exit 3-3
Media Path2
Diverter gate
3-3
Eject clamp hp 3-3
Front tamper hp 3-3
Media eject shaft hp 3-3
Rear tamper hp 3-3
Punch and Staple
Low staple
3-3
Punch box set 3-3
Punch cam front 3-3
Punch carriage shift hp 3-3
Punch hole select 3-3
Punch side reg1 3-3
Punch side reg2 3-3
Punch unit hp 3-3
Punch waste full 3-3
Stapler carriage shift hp 3-3
Staple Test 3-2
front door
parts catalog
7-8
H
handling ESD-sensitive parts 4-1
I
installation, confirm status 2-2
L
left lower cover 4-28
left upper cover 4-29
locations
bridge unit assembly
5-1
buffer, upper exit, lower exit and drive motors 5-6
cables 5-7
diverter and media eject 5-4
finisher control card assembly 5-6
media eject and media compiler 5-5
To Next Page
Loading...
