I-4 Finisher Service Manual
4024-XXX
sensor (media eject clamp HP)
4-67
sensor (media eject shaft HP) 4-79
sensor (punch cam front) 4-49
sensor (punch carriage shift HP) 4-51
sensor (punch hole select) 4-49
sensor (punch unit HP) 4-49
sensor (punch unit motor encoder) 4-48
sensor (punch unit side registration pair) 4-44
sensor (punch waste box full) 4-53
sensor (punch waste box set) 4-52
sensor (rear tamper HP) 4-72
sensor (stacker bin level 1) 4-34
sensor (stacker bin level 2) 4-34
sensor (stacker bin level encoder) 4-35
sensor (stacker bin no media) 4-36
sensor (stacker bin upper limit) 4-36
sensor (stapler carriage HP) 4-58
sensor (upper media bin full) 4-108
sensor (upper media exit) 4-104
stacker bin lift motor assembly 4-38
stacker media bin assembly 4-22
stapler unit assembly 4-56
stapler unit frame 4-54
sub paddle 4-63
sub paddle drive shaft assembly 4-64
switch (eject cover interlock) 4-68
switch (finisher front door interlock) 4-26
top cover 4-19
upper media bin assembly 4-20
upper media bin front cover 4-25
upper media exit pinch roll assembly 4-105
upper media exit roll assembly 4-106
upper media transport roll assembly 4-111
upper pinch guide assembly 4-109
S
safety information v-xiii
safety inspection guide 6-1
sensors
bridge unit media entrance
4-16, 5-1
bridge unit media exit 4-17, 5-1
bridge unit top cover interlock 4-15, 5-1
buffer path 4-93
compiler media in 4-73
diverter gate 4-110
finisher media entrance) 4-98
front tamper HP 4-72
lower media exit 4-80, 5-4
media eject clamp HP 4-67, 5-4
media eject shaft HP 4-79
punch cam front 4-49, 5-3
punch carriage shift HP 4-51, 5-3
punch hole select 4-49, 5-3
punch unit HP 4-49, 5-3
punch unit motor encoder 4-48
punch unit side reg 1 5-3
punch unit side reg 2 5-3
punch unit side registration pair with bracket 4-44
punch waste box full 4-53, 5-3
punch waste box set 4-52
punch waste box set) 5-3
rear tamper HP 4-72
stacker bin level 1 4-34, 5-2
stacker bin level 2 4-34, 5-2
stacker bin level encoder 4-35
stacker bin no media 4-36
stacker bin upper limit 4-36, 5-2
stapler carriage HP 4-58, 5-2
upper media bin full 4-108
upper media exit 4-104
service checks 2-11
service checks, using 2-1
stacker unit
locations
5-2
media bin assembly 4-22
stacker bin lift motor assembly 4-38
staple unit
locations
5-2
parts catalog 7-14
stapler carriage motor assembly 5-2
stapler unit assembly 4-56
stapler unit frame 4-54
sub paddle
removals
4-63
sub paddle drive shaft assembly 4-64
switches
eject cover interlock
4-68, 5-4
finisher front door interlock 4-26, 5-2
T
tests
Bridge media ent
3-3
Bridge media exit 3-3
Buffer path 3-3
Compiler media in 3-3
Cover F bridge top 3-3
Diverter gate 3-3
Door G fin front 3-3
Eject clamp hp 3-3
Feed Tests 3-2
Fin media enter 3-3
Fin upper bin full 3-3
Front tamper hp 3-3
Fuser exit 3-3
Hole Punch Test 3-2
Low staple 3-3
Lower media exit 3-3
Media eject shaft hp 3-3
Punch box set 3-3
Punch cam front 3-3
Punch carriage shift hp 3-3
Punch hole select 3-3
Punch side reg1 3-3
Punch side reg2 3-3
Punch unit hp 3-3
Punch waste full 3-3
Rear tamper hp 3-3
Stacker bin level encod 3-3
Stacker bin level1 3-3
Stacker bin level2 3-3
To Next Page
Loading...
