NETGEAR FVS318G User Manual

Monitor System Access and Performance
368
NETGEAR ProSAFE VPN Firewall FVS318G v2
IPv6 Address The IPv6 address of the WAN port. For information about configuring the IPv4
address of the WAN port, see Configure the IPv6 Internet Connection and WAN
Settings on page 38.
WAN State The WAN state can be either UP or DOWN, depending on whether the port is
connected to the Internet.
NAT (IPv4 only) The NAT state can be either Enabled or Disabled, depending on whether NAT is
enabled (see Network Address Translation on page 27) or classical routing is
enabled (see Classical Routing on page 27).
IPv4 Connection Type The connection type can be Static IP, DHCP, PPPoE, or PPTP, depending on
whether the WAN address is obtained dynamically through a DHCP server or
assigned statically by you. For information about connection types, see Configure
the IPv4 Internet Connection and WAN Settings on page 26.
IPv6 Connection Type The connection type can be Static IPv6, PPPoE, or Dynamic IP (DHCPv6),
depending on whether the WAN address is obtained dynamically through a DHCP
server or ISP or assigned statically by you. For information about connection
types, see Configure the IPv6 Internet Connection and WAN Settings on page 38.
IPv4 Connection State The IPv4 connection state can be either Connected or Not Connected, depending
on whether the WAN interface is connected to the Internet over an IPv4 address.
For information about configuring the IPv4 address of the WAN port, see
Configure the IPv4 Internet Connection and WAN Settings on page 26.
IPv6 Connection State The IPv6 connection state can be either Connected or Not Connected, depending
on whether the WAN interface is connected to the Internet over an IPv6 address.
For information about configuring the IPv6 address of the WAN port, see
Configure the IPv6 Internet Connection and WAN Settings on page 38.
Link State The link state can be either LINK UP or LINK DOWN, depending on whether the
WAN port is physically connected to a modem, dish, or router. For information
about connecting a WAN port, see the NETGEAR ProSAFE VPN Firewall
FVS318G v2 Installation Guide.
Gateway The IP address of the gateway.
These IPv4 settings are either
obtained dynamically from your ISP or
specified by you on the Broadband
ISP Settings (IPv4) screen (see
Manually Configure an IPv4 Internet
Connection on page 31).
Primary DNS Server The IP address of the primary DNS
server.
Secondary DNS Server The IP address of the secondary DNS
server.
Gateway (IPv6) The IP address of the gateway.
These IPv6 settings are either
obtained dynamically from your ISP or
specified by you on the Broadband
ISP Settings (IPv6) screen (see
Configure a Static IPv6 Internet
Co
nnectio
n on page 42).
Primary DNS Server
(IPv6)
The IP address of the primary DNS
server.
Secondary DNS Server
(IPv6)
The IP address of the secondary DNS
server.
Table 82. Detailed Status screen information (continued)
Item Description

NETGEAR FVS318G Specifications

General

Power requirements	12V DC, 1.5A
Firewall throughput	250 Mbit/s
Maximum data transfer rate	1000 Mbit/s
HTTP performance	6000 transactions/sec
Wi-Fi	No
DHCP server	Yes
Number of VLANs	256
VPN tunnels quantity	12
WAN connection	Ethernet (RJ-45)
Connectivity technology	Wired
Ethernet LAN (RJ-45) ports	9
Ethernet DMZ ports quantity	1
Routing protocols	RIP-1, RIP-2
Supported network protocols	TCP/IP, UDP, ICMP, PPPoE
VPN support	IPsec (ESP), IKE, PKI, HTTPS
Security algorithms	128-bit AES, 192-bit AES, 256-bit AES, 3DES, DES, MD5, SHA-1
Internal memory	128 MB
Flash memory	32 MB
Storage media type	Flash
Processor frequency	300 MHz
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Cables included	LAN (RJ-45)

Weight and Dimensions

Weight	590 g
Dimensions (WxDxH)	190 x 125 x 35 mm