Trap Parameters Appendix Q
WinLink™ 1000 User Manual Release 1.9 Q-21
swVersionsMismatchRestrictedCompatibilityAlarm 115 minor The trap is sent if SW versions mismatch with restricted link
functionality.Contains a single parameter, which is its description:1 -
Description: Software versions mismatch - restricted link functionality
swVersionsMismatchSoftwareUpgradeRequired 116 major The trap is sent if SW versions mismatch and SW upgrade is
required.Contains a single parameter, which is its description:1 -
Description: Software versions mismatch - Software upgrade required
swVersionsIncompatible 117 critical The trap is sent if SW versions are incompatible.Contains a single
parameter, which is its description:1 - Description: SW Versions
incompatible
hssMultipleSourcesDetectedAlarm 118 major Indicates that multiple sync pulse sources were detected.Contains a
single parameter, which is its description:1 - Description: HSS multiple
sync sources were detected.
hssSyncToProperSourceStoppedAlarm 119 major Indicates that synchronization to a proper sync pulse source was
stopped.Contains a single parameter, which is its description:1 -
Description: HSS sync pulse - Down. The reason is: %s.%s - Is the
reason for the sync down.
hssSyncPulseDetectedAlarm 120 major Indicates that HSS additional sync pulse was detected.Contains a single
parameter, which is its description:1 - Description: HSS additional sync
pulse was detected.
tdmBackupAlarm 121 major Indicates that the TDM backup link was activated.Contains a single
parameter, which is its description:1 - Description: TDM backup alarm -
backup link was activated.
linkLockUnauthorizedRemoteODU 122 major Indicates that the remote ODU is unauthorized. Contains a single
parameter, which is its description:1 - Description: Unauthorized remote
ODU connection rejected.
linkLockUnauthorizedODU 123 major Indicates that the ODU is unauthorized. Contains a single parameter,
which is its description:1 - Description: Unauthorized ODU connection
rejected.
hotStandbyAlarm 124 major Indicates that the hot standby secondary link was activated.Contains a
single parameter, which is its description:1 - Description: Secondary Link
Is Active.
sfpInsertion 126 normal Indicates that a device was inserted to SFP Port
sfpPort1DisconnectedAlarm 127 major Indicates the SFP port 1 status changed to disconnected.Contains a
single parameter which is its description:1 - Description: SFP port 1 status
changed to disconnected.
tdmServiceClear 200 normal Indicates that TDM Service fault is cleared.Contains a single parameter,
which is its description:1 - Description: TDM Service - Normal.
ethServiceOpened 201 normal Indicates that Ethernet Service has been opened.Contains a single
parameter, which is its description:1 - Description: Ethernet Service has
been opened.
encryptionClear 203 normal Indicates that encryption is OK.Contains a single parameter, which is its
description:1 - Description: Encryption Status - Normal.
changeLinkPasswordClear 204 normal Indicates that the Link Password was changed successfully.Contains a
single parameter, which is its description:1 - Description: Link Password
has been changed at/on: %s.%s - Is the Local Site name or Remote Site
name or both sides of the Link.
externalAlarmInPort1Clear 205 normal This Trap is sent every time an External Alarm Input fault of port # 1 is
cleared.Contains a single parameter, which is its description:1 -
Description: External Alarm 1 - <User Text> - Alarm Cleared.
externalAlarmInPort2Clear 206 normal This Trap is sent every time an External Alarm Input fault of port # 2 is
cleared.Contains a single parameter, which is its description:1 -
Description: External Alarm 2 - <User Text> - Alarm Cleared.
lanPort1Clear 209 normal Indicates the LAN port 1 status changed to connected.Contains two
parameters:1 - Description: LAN port 1 status changed to connected -
%s2 - %s Is the Eth. mode (speed & duplex)
lanPort2Clear 210 normal Indicates the LAN port 2 status changed to connected.Contains two
parameters:1 - Description: LAN port 2 status changed to connected -
%s.2 - %s Is the Eth. mode (speed & duplex).
Table Q-3: MIB Traps (Sheet 3 of 4)
Name ID Severity Description
To Next Page
Loading...
