Cisco 7925G Administration Guide

Possible explanation and actionDescriptionStatus message
For information about how to manage the LSC for your phone, see the
“Using the Certificate Authority Proxy Function” chapter in
Cisco Unified Communications Manager Security Guide.
The LCS was updated successfully
on the phone.
LCS operation
complete
Contact the Cisco TAC.The phone does not recognize an
error code provided by the TFTP
server.
TFTP Error
•
The DHCP server is not configured properly and is not providing
the correct TFTP server address. In this case, update the TFTP
server configuration to specify the correct TFTP server.
•
If the phone is using a static IP address, the phone may be
configured with the wrong TFTP server address. In this case,
enter the correct TFTP server address in the Network
Configuration menu on the phone.
•
If the TFTP server address is correct, there may be a problem
with the CTL file. In this case, run the CTL client and update the
CTL file, making sure that the proper TFTP servers are included
in this file.
The specified TFTP server could not
be found in the phone CTL.
TFTP server not
authorized
•
Network is busy: The errors should resolve themselves when the
network load reduces.
•
No network connectivity between the TFTP server and the phone:
Verify the network connections.
•
TFTP server is down: Check configuration of TFTP server.
TFTP server did not respond.TFTP timeout
View Configuration File Name
You can use the Settings menu and Status menu to determine the name of the configuration file for the Cisco
Unified Wireless IP Phone.
To locate the configuration file name, follow these steps:
Procedure
Step 1
Choose SETTINGS > Status.
Step 2
Select Status Messages.
The phone displays the name of the configuration file in the following format:
SEPmacaddress.cnf.xml or SEPmacaddress.cnf.xml.enc.sgn.
Step 3
To exit the screen, press Back.
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
188
Security, Device, Model, Status, and Call Statistics Information
View Status Messages Screen

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g