Cisco 7925G Administration Guide

Status Messages
Table 39: Status Messages, Description, Possible Explanation, and Action
Possible explanation and actionDescriptionStatus message
For information about how to manage the MIC for your phone, see the
“Using the Certificate Authority Proxy Function” chapter in
Cisco Unified Communications Manager Security Guide.
The manufacturing installed
certificate (MIC) that is used for
security features is corrupted.
Bad MIC on phone
The configuration file for a phone is created when the phone is added
to the Cisco Unified Communications Manager database. If the phone
has not been added to the Cisco Unified Communications Manager
database, the TFTP server generates a CFG File Not Found response.
•
Phone is not registered with Cisco Unified Communications
Manager.
You must manually add the phone to
Cisco Unified Communications Manager if you are not allowing
phones to autoregister. See Cisco Unified Communications
Manager Phone Addition Methods, on page 48 for details.
•
If you are using DHCP, verify that the DHCP server is pointing
to the correct TFTP server.
•
If you are using static IP addresses, check configuration of the
TFTP server. See IP Network Settings, on page 92 for details
on assigning a TFTP server.
Neither the name-based configuration
file nor default configuration file
were not found on the TFTP Server.
CFG file not found
None. This message is informational only.
For more information about the CTL file, see Cisco Unified
Communications Manager Security Guide.
A certificate trust list (CTL) file is
installed in the phone.
CTL Installed
Problem with the CTL file on the TFTP server.
For more information, see Cisco Unified Communications Manager
Security Guide.
The phone could not update its
certificate trust list (CTL) file.
CTL update failed
•
If the phone has a static IP address, verify that you have not
assigned a duplicate IP address. See IP Network Settings, on
page 92 section for details.
•
If you are using DHCP, check the DHCP server configuration.
Another device is using the IP
address assigned to the phone.
Duplicate IP
For information about how to manage the LSC for your phone, see the
“Using the Certificate Authority Proxy Function” chapter in
Cisco Unified Communications Manager Security Guide.
The locally significant certificate
(LSC) that is used for the security
features did not install properly.
LCS operation failed
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
187
Security, Device, Model, Status, and Call Statistics Information
View Status Messages Screen

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g