Cisco 7925G Administration Guide

DescriptionItem
True: Save trace logs after powering off the phone
False: Delete trace logs
Preserve Logs
You can enable debugging by configuring various settings on the Trace
Configuration. These options determine how trace settings are handled
when you reboot:
•
Yes: Default value. Settings will be reset to the default values upon
reboot.
•
No: Trace settings will not reset upon reboot.
Reset Trace Settings upon
Reboot
Related Topics
Access Phone Web Page, on page 69
Network Profiles, on page 74
Set Up USB Settings on PC, on page 95
System Settings, on page 104
Set Up Wavelink Settings
The Cisco Unified Wireless IP Phone supports the use of the Wavelink Avalanche server to configure the
phone, which can be set up as a Wavelink Avalanche client device. Configuration Utility for Wavelink
Avalanche can be installed on the Wavelink Avalanche server to configure a single phone or multiple phones
with common settings. For more information, see Wavelink Avalanche Server, on page 133.
You can use the phone web page to assign attributes to the phone that can be used to distinguish it from other
mobile devices connected to the Wavelink server. These attributes can be used as search criteria for locating
phones on the Wavelink server. For example, the predefined ModelName parameter with a value of CP7925G
identifies a device as a Cisco Unified Wireless IP Phone 7925G or Cisco Unified Wireless IP Phone 7925G-EX,
while CP7926 identifies a device as a Cisco Unified Wireless IP Phone 7926G.
By default, the parameters are configured as follows:
•
ModelName = CP7925 or CP7926
•
EnablerVer = 3.11-01
For more information about using the Wavelink Avalanche server, see Wavelink Server IP Address Setup,
on page 134.
Note
To configure Wavelink parameters using the phone web page, follow these steps:
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
99
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Web Pages
Set Up Wavelink Settings

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g