Cisco 7925G Administration Guide

this URL: http://www.cisco.com/en/US/products/hw/phones/ps379/products_implementation_design_guides_
list.html.
The Cisco Unified Wireless IP Phone 7926G must be running Firmware Version 1.4(1) or later.Note
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Setup in Cisco
Unified Communications Manager
To add phones to the Cisco Unified Communications Manager Administration, you can use:
•
Autoregistration
•
Cisco Unified Communications Manager Administration
•
Bulk Administration Tool (BAT)
•
BAT and the Tool for Auto-Registered Phones Support (TAPS)
For general information about configuring phones in Cisco Unified Communications Manager, see the “Cisco
Unified IP Phone” chapter in the Cisco Unified Communications Manager System Guide.
Related Topics
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Installation, on page 20
Cisco Unified Communications Manager Phone Addition Methods, on page 48
Features, Templates, Services, and Users, on page 147
Cisco Unified Communications Manager Setup for Cisco Unified Wireless IP Phone 7925G, 7925G-EX,
and 7926G, on page 241
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Installation
After you have added the phones to the Cisco Unified Communications Manager Administration, you can
complete the phone installation. You can install the phone or the user can install the phone. The Cisco Unified
Wireless IP Phone 7925G, 7925G-EX, and 7926G Installation Guide provides directions for assembling the
phone and accessories and charging the battery.
Before using the phone to connect to the wireless LAN, you need to configure a network profile for the phone.
You can use the phone web pages to set up the network profile and other phone settings, or you can configure
the network profile using the menus on the phone.
If you use autoregistration that is part of Cisco Unified Communications Manager Administration, you need
to update the specific configuration information for the phone such as associating the phone with a user,
changing the softkey template, or changing the directory number (DN).
Before you install a phone, even if it is new, upgrade the phone to the current firmware image. For
information about upgrading, see the readme file for your phone which is located at: http://www.cisco.com/
cgi-bin/tablebuild.pl/ip-7900ser-crypto.
Note
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
20
Cisco Unified Wireless IP Phone
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Setup in Cisco Unified Communications Manager

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g