EasyManuals Logo

Cisco 7925G Administration Guide

Cisco 7925G
274 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #130 background imageLoading...
Page #130 background image
Trace Logs, on page 105
Upgrade Phone Firmware, on page 108
Backup Settings Area, on page 105
Site Survey Report
Before the Site Survey Report is generated for viewing from the phone web page, you must first run the Site
Survey utility from the phone. For more information, see Perform Site Survey, on page 46.
To view the report, go to the phone web page and choose Site Survey from the left pane. An HTML report
in the form of a neighbor table of Access Points (AP) displays.
You can also run the Neighbor List utility from the phone to display a list of current APs on the phone.
However, this utility will not generate the Site Survey Report that you can access from the phone web
page. See also Display Neighbor List, on page 45.
Note
The neighbor table provides a matrix of APs observed during the site survey. Depending on the extent of the
survey, not all observed APs will be considered a best AP or an immediate neighbor.
The Site Survey Report stores information about each AP until it reaches a limit of 256 APs. For each AP,
up to ten neighbors are tracked.
The following table shows the information shown in the site survey report.
Table 24: Site Survey Report Neighbor Table
Description or indicatorInformation
The Service Set Identifier (SSID) used during Site Survey is displayed in the
report title.
Report title
Information displayed in cell with yellow background and where the row
heading matches the column heading (for example, 64%-60/-43):
Percentage of time it is the best AP.
Received Signal Strength Indicator (RSSI) range during the time it is
the best AP.
A low number (below -65) may indicate insufficient overlap between
the best AP and its neighbors.
Note
Best AP
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
110
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Web Pages
Site Survey Report

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals