EasyManuals Logo

Cisco 7925G Administration Guide

Cisco 7925G
274 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #141 background imageLoading...
Page #141 background image
DHCP Settings
The Cisco Unified IP Phones enable DHCP, by default, to automatically assign IP addresses to devices when
you connect them to the network. If you do not use DHCP in your network, then you must disable DHCP and
manually enter the network configuration information.
Use these guidelines when manually configuring the IP settings:
Ensure the TFTP server has an IP address.
Ensure the default router IP address is on the same subnet as the host IP address.
When DHCP is enabled, you cannot configure IP settings, but you can configure an alternate TFTP server.Note
Related Topics
Dynamic Host Configuration Protocol Server Interactions, on page 38
Disable DHCP
To disable DHCP on the phone and manually configure IP settings, follow these steps:
Procedure
Step 1
Choose SETTINGS > Network Profiles.
Step 2
Scroll to the profile name that you want to configure and press the View softkey.
Step 3
Enter **# to unlock the profile and press Edit.
Step 4
Select Network Configuration. Press View.
Step 5
Scroll to DHCP Enabled and press No.
Step 6
Scroll to IP Address and press Select.
Step 7
In the New IP Address field, enter the static IP address for the phone.
Step 8
Press Options > Validate to save the entry or press Options > Cancel.
Step 9
After you disable DHCP, you must enter the other required static fields. See Static Settings with Disabled
DHCP, on page 122 for descriptions of these fields.
For information about entering values, see Network Profile Data Input Guidelines, on page 118.
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
121
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Settings
DHCP Settings

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals