EasyManuals Logo

Cisco 7925G Administration Guide

Cisco 7925G
274 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #88 background imageLoading...
Page #88 background image
Windows XP 32 bit
Windows 7 32 bit
Windows 7 64 bit
Related Topics
Backup Settings Area, on page 105
Install USB Drivers
To install the drivers on your PC, perform the following steps.
Procedure
Step 1
Log in to Cisco.com.
Step 2
Download the installation package and read me file for the USB drivers from this location:
http://www.cisco.com/cgi-bin/tablebuild.pl/ip-7900ser-crypto
Before proceeding, review the read me file for specific instructions for your PC operating system.Note
Step 3
Double-click on the USB installation file (listed in the read me file) to start the installation program.
Step 4
Follow the prompts in the InstallShield Wizard.
If you receive a Hardware Installation warning message stating that the software has not passed
Microsoft Windows Logo testing, click Continue.
Note
Step 5
When you see the Finished screen, the installation is complete. Close the wizard.
Step 6
Plug the USB cable into the USB port on the PC and into the USB connector on the phone.
The Found New Hardware Wizard dialog box opens.
Step 7
To update the new software, click the button next to Yes, this time only and click Next.
Step 8
Click the button next to Install the Software automatically (Recommended).
After 2 to 3 minutes, the software installs and a message appears on the task bar stating Found New
Hardware - Software installed and ready to use.
Step 9
Click Finish when the installation completes.
The phone briefly displays USB Connected on the status line.
Set Up USB LAN on PC
To configure the USB LAN connection on your PC, follow these steps:
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
68
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Web Pages
Install USB Drivers

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals