Why can't I access environment parameters in DL.CODE for my Datalogic Industrial Equipment?
To resolve the issue of being unable to access environment parameters in DL.CODE (Device>Settings>Settings menu item is gray) for your Datalogic Industrial Equipment, verify that you are using the Installer - Expert User level. If not, change it in the Options>Change User menu.
What to do if the trigger LED is not blinking in One Shot or Phase Mode using serial trigger source on Datalogic Industrial Equipment?
If the "TRIGGER" LED is not blinking in One Shot or Phase Mode using a serial trigger source on your Datalogic Industrial Equipment, check the settings for Acquisition Trigger, Reading Phase-ON, and Reading Phase-OFF parameters on the Reading Phase step. Ensure that the COM port parameters (Baud Rate, Parity, Data Bits, Stop Bits) are correctly assigned. On the Reading Phase step, verify the settings of Acquisition Trigger String, Reading Phase-ON String, and Reading Phase-OFF String parameters. Also, confirm that the serial trigger source is correctly connected.
Why is no image displayed in DL.CODE when the trigger LED is blinking in Phase Mode on Datalogic Industrial Equipment?
If the "TRIGGER" LED is correctly blinking in Phase Mode but no image is displayed in the DL.CODE window for your Datalogic Industrial Equipment, determine if the Phase frequency is lower than the maximum frame rate.
What to do if the trigger LED is not blinking in Continuous Mode on Datalogic Industrial Equipment?
If the "TRIGGER" LED is not blinking in Continuous Mode on your Datalogic Industrial Equipment, verify the correct software configuration settings.
What to do if the trigger LED is blinking but no result is transmitted by Datalogic Industrial Equipment?
If the "TRIGGER" LED is correctly blinking on your Datalogic Industrial Equipment but no result is transmitted at the end of the reading phase collection, check the Code Collection parameters on the Reading Phase step and the Data Formatting parameters on the Data Formatting step.
What to do if the power LED is not lit on Datalogic Industrial Equipment?
If the "POWER" LED is not lit on your Datalogic Industrial Equipment, check the following: Is the power connected? If you're using a power adapter (like PG6000), is it connected to the wall outlet? If using rail power, does the rail have power? If using a CBX, does it have power (check the switch and LED)? Determine whether you're using the M12 17-pin connector or the CBX spring clamp connectors. Measure the voltage either at pin 1 and pin 2 (for the 17-pin connector) or at the spring clamp Vdc and GND (for CBX).
What to do if Datalogic Industrial Equipment always transmits the No Read Message?
To address the issue of the Datalogic Industrial Equipment reader always transmitting the No Read Message, follow these steps: Run the Rapid Configuration procedure. Position the reader as described in "Mounting And Positioning Matrix 320". Through DL.CODE, tune the Acquisition Delay on Trigger if the moving code is out of the reader's field of view. Set the Continuous Operating Mode if no external trigger source is available. Tune the Image Settings to improve the code image quality. Check the parameter settings in the Advanced Setup step for 2D Codes, 1D Codes, and Postal Codes. View the full resolution code image to check the printing or marking quality.
What to do if data transferred to the host from Datalogic Industrial Equipment is incorrect?
To resolve issues with incorrect, corrupted, or incomplete data being transferred to the host from your Datalogic Industrial Equipment, ensure that the host serial port settings match the reader's settings. In DL.CODE, check the Header and Terminator String parameters in the Data Formatting step. Also, review the various Message Field parameter settings in the Data Formatting step.
General| Protection | IP65 |
|---|---|
| Storage Temperature | -20°C to 70°C |
| Reading Distance | 50 mm to 1, 200 mm |
| Connectivity | USB, RS-232 |
| Power Supply | 5V DC |
| Operating Temperature | 0°C to 50°C |
| Scanning Distance | 50 mm to 1, 200 mm |
| Interface | RS-232, Ethernet |
| Supported Barcodes | 1D, 2D |
| Humidity | 5% to 95% (non-condensing) |
| Drop Specification | 1.5 m |
| Lighting | LED |
| Audible Feedback | Beeper |
| Visual Feedback | LED |
| Technology | 2D Imager |
To Next Page
