3 Devices
DVP-20PM Application Manual
3-22
Special
D
device
Function 20D 20M
Off
On
STOP
RUN
RUN
STOP
Attribute Latching Default Page
D1500
Data block used by FROM/TO
It corresponds to CR#0.
○ ○ H6260 - - R No H6260 -
D1501
↓
D1699
Data block used by FROM/TO
They correspond to CR#1~CR#199.
○ ○ 0 - - R/W No 0 -
D1700 Ox motion subroutine which is executed ○ ○ 0 - - R No 0 -
D1702
Step address which is executed in the Ox motion
subroutine
○ ○ 0 - - R No 0 -
D1703*
M-code which is executed in the Ox motion
subroutine
○ ○ 0 - - R No 0 3-36
D1704
Dwell duration of the Ox motion subroutine which
is set
○ ○ 0 - - R No 0 -
D1705
Present dwell duration of the Ox motion
subroutine
○ ○ 0 - - R No 0 -
D1706
Number of times the instruction RPT in the Ox
motion subroutine is executed
○ ○ 0 - - R No 0 -
D1707
Number of times the instruction RPT in the Ox
motion subroutine has been executed
○ ○ 0 - - R No 0 -
D1708 Compensation value for the X-axis (low word)
D1709 Compensation value for the X-axis (high word)
○ ○ 0 - - R No 0 -
D1710
Compensation value for the center of the arc
created by the X-axis (low word)
D1711
Compensation value for the center of the arc
created by the X-axis (high word)
○ ○ 0 - - R No 0 -
D1712 Compensation value for the radius (low word)
D1713 Compensation value for the radius (high word)
○ ○ 0 - - R No 0 -
D1724 Compensation value for the Y-axis (low word)
D1725 Compensation value for the Y-axis (high word)
○ ○ 0 - - R No 0 -
D1726
Compensation value for the center of the arc
created by the Y-axis (low word)
D1727
Compensation value for the center of the arc
created by the Y-axis (high word)
○ ○ 0 - - R No 0 -
D1736 Dwell duration of O100 which is set ○ ○ 0 - - R No 0 -
D1737 Present dwell duration of O100 ○ ○ 0 - - R No 0 -
D1738
Number of times the instruction RPT in O100 is
executed
○ ○ 0 - - R No 0 -
D1739
Number of times the instruction RPT in O100 has
been executed
○ ○ 0 - - R No 0 -
D1796*
Speed to which the speed of the continuous
interpolation decreases
○ ○ 0 - - R No 0 3-37
D1798*
Percentage for the values of the speed
parameters of the G-codes
○ ○ 0 - - R No 0 3-38
D1799* Polarities of the input terminals ○ ○ 0 - - R/W No 0 3-38
D1800* States of the input terminals ○ ○ 0 - - R No 0 3-38
D1802* O100 error code ○ ○ 0 - - R/W No 0 3-39
D1803* Step address in O100 at which an error occurs ○ ○ 0 0 - R/W No 0 3-39
D1804* Polarities of the input terminals
╳
○ 0 - - R/W No 0 3-39
D1805* States of the input terminals
╳
○ 0 - - R No 0 3-39
D1806 Filter coefficient for the input terminals ○ ○ 0 - - R/W No 0 3-39
D1816* Setting the parameters of the X-axis ○ ○ - - - R/W Yes 0 3-40
D1818
Number of pulses it takes for the motor of the
X-axis to rotate once (low word)
D1819
Number of pulses it takes for the motor of the
X-axis to rotate once (high word)
○ ○ - - - R/W Yes 2000 -
To Next Page
Loading...
