What to do if the Epson Printer's PAPER light is lit even with paper installed?
If the PAPER light is lit on your Epson printer even with paper installed, it may be due to: 1. The left tractor being too far to the right. Move the left tractor to the far left so that the paper covers the paper out sensor.
Why does my Epson Printer paper not feed reliably, causing tears and jams?
Unreliable paper feed in your Epson printer, leading to frequent tears or paper jams, can be due to several factors: 1. The paper supply may not be aligned correctly with the paper feed tractors; ensure it is properly aligned. 2. The paper might be stretched too tightly. Slightly reduce tension by adjusting the right tractor closer to the left one. 3. The front feed path could be obstructed. Make sure it is clear and consider using the bottom feed path instead. 4. The paper might be catching on the paper box. Trim the box or remove the paper from it. 5. The paper might be too heavy or light for the front feed path. Consider using the bottom feed path.
What to do if my Epson Printer has no printout?
If your Epson printer is producing no printout, consider the following: * Ensure that a ribbon cartridge is installed correctly. Re-install the ribbon cartridge if necessary. * Check the ribbon to make sure it is not twisted.
What to do if my Epson Printer has PAPER Flashing?
If the PAPER light is flashing on your Epson printer, this indicates a paper jam. Clear the jam to resolve the issue.
What to do if an e-mail message is not sent when a problem occurs with an Epson Software projector?
If an e-mail message isn't being sent when a problem occurs with an Epson projector, check that the SMTP server IP address, Port Number, and Recipient mail address have all been set correctly. Also, ensure the projector's Standby Mode is set to Communication On (or Network On) or Network Monitoring is set to On in the configuration menu. If a critical problem has caused the projector to momentarily stop working, it cannot send e-mail messages; in this case, if the projector cannot be reset even after it has been checked, contact Epson.
Why won't the scanner read barcodes on my Epson Printer?
If the scanner on your Epson printer is unable to read barcodes, it may be due to: 1. The barcode density being too low. Set the density in the configuration menu to 100 dpi. 2. Vertical misalignment during bi-directional printing. Re-adjust vertical alignment in the configuration menu. If necessary, turn off bi-directional printing in the configuration menu. 3. A worn-out ribbon. Replace the ribbon. Try double strike printing.
What causes fading print on my Epson Printer and how can I fix it?
Fading print on your Epson printer can be attributed to: 1. A worn-out ribbon. Replace the ribbon. 2. The ribbon not advancing, or a motor or electronics failure. Re-install or replace the ribbon.
Why is my Epson Printer printing characters too light?
If the characters printed by your Epson printer are too light, it could be due to: 1. The printhead gap being too wide. Adjust the printhead gap. 2. A worn-out ribbon. Replace the ribbon.
What to do if my Epson Printer is smudging?
If your Epson printer is smudging, consider the following: 1. The printheads may be too close to the paper. Re-adjust the printhead gap. 2. The ribbon and/or ribbon guides may be worn. Examine and replace the ribbon cartridge if necessary.
How to fix Epson Software when projectors cannot be monitored or controlled?
If Epson projectors cannot be monitored or controlled, first, ensure the network cable is correctly connected; reconnect if necessary. Check the Network configuration settings. Next, uninstall and reinstall EasyMP Monitor. Then, register the projectors you intend to control or monitor. Finally, verify that the projector's Standby Mode is set to Communication On (or Network On) or Network Monitoring is set to On in the configuration menu. When the projector is in standby mode, the projector's Standby Mode must be set to Communication On (or Network On) or Network Monitoring must be set to On in the configuration menu in order to use EasyMP Monitor to monitor and control the projector.
To Next Page
General