·18·
Operating manual
CNC 8070
(REF: 1505)
Ref. 0809
Edisimu mode. To simulate the program, when pressing the "START" softkey,
the CNC assumes the real configuration of the spindles of the channel and the
configuration of the machine parameters. The starting coordinates for
simulation will be the real coordinates that the CNC had on power-up.
Edisimu mode. New window for consulting the status of the subroutines,
canned cycles, block repetition and loops.
Edisimu mode. The "START" softkey saves the program being edited.
Automatic mode. New functions and instructions that cancel the retrace
function.
Automatic mode. New window for consulting the status of the subroutines,
canned cycles, block repetition and loops.
Automatic mode. The [START] key saves the program being edited.
Diagnosis mode. Generate the Fagor file for error diagnosis.
Tool table. When selecting an incremental wear, it is possible to define the
maximum increment possible; by default 0.5 mm (0.019685 inch).
Machine parameters tables. Import and export leadscrew compensation
tables.
Within a work mode, select the different pages in reverse order using the
[SHIFT] key.
Setup assistance. Bode.
Interface related variables.
Software V04.00 (it does not include the features of version V03.21)
Unicode.
New language (Chinese).
In the machine parameter table, an icon indicates which parameters are
involved in parameter matching.
Handwheels. There can now be up to 12 handwheels. • Machine parameter: NMPG.
The CNC applies module compensation throughout the entire revolution of the
axis.
• Machine parameter: MODCOMP.
Home search moving the axis to the reference point. • Machine parameter: POSINREF.
PLC. There can now be up to 1024 PLC messages. • PLC resources: MSG.
PLC. There can now be up to 1024 PLC errors. • PLC resources: ERR.
Handwheels. Inhibit the handwheels of the system. • PLC mark: INHIBITMPG1/INHIBITMPG12.
Cancel spindle synchronization after executing M02, M30 or after an error or
a reset.
• Instructions #SYNC and #TSYNC.
Positioning a turret magazine whether there is a tool in the indicated position
or not.
• #ROTATEMZ instructions.
A channel maintains its master spindle after executing M02, M30 or after an
emergency or a reset or restarting the CNC.
• #MASTERinstruction.
Force the change of gears and/or of the parameter set of a Sercos drive • Variable: (V.)A.SETGE.xn
Set a machine coordinate. • Function G174.
There can now be up to 99 zero offsets. • Function G159.
There can now be up to 100 synchronization marks. • Instructions #MEET, #WAIT and #SIGNAL.
Select a turret position. • #ROTATEMZ instructions.
Axis synchronization. Managing a rotary axis as an infinite axis making it
possible to increase the feedback count of the axis indefinitely (wihout limits)
regardless of the value of the module.
• Variables: (V.)[ch].A.PREVACCUDIST.xn
Variables. The variable (V.)[ch].E.PROGSELECT can be written via part-
program, PLC and interface. This variable can only be written with the value
of ·0·
• Variables: (V.)[ch].E.PROGSELECT
Variables. The following variables are valid for the spindle. • Variables: (V.)[ch].A.MEAS.sn
(V.)[ch].A.ATIPMEAS.sn
(V.)[ch].A.MEASOF.sn
(V.)[ch].A.MEASOK.sn
(V.)[ch].A.MEASIN.sn
Profile editor.
• Programming in Polar coordinates.
• Programming in incremental coordinates.
• Best zoom, display part zero and auto-zoom from the keyboard.
• Improved softkey menu.
Manual (jog) mode. New softkey to turn the CNC off.
Manual (jog) mode. In handwheel mode, next to each axis, the CNC indicates
whether that axis has an individual handwheel associated with it or not.
Manual (jog) mode. The screen shows the tool dimensions.
Automatic mode. The screen shows the tool dimensions.
Handwheels. The general handwheels can move axes with an associated
individual handwheel.
Handwheels. Number of pulses sent by the handwheel since the system was
started up.
• Variables: (V.)G.HANDP[hw]
Feed handwheel.
Diagnosis mode. View the history of errors and warnings issued by the CNC.
Software V03.20
To Next Page
Loading...
