GE MDS ORBIT ECR - 3.8.19 Network Monitor Service

320 MDS Orbit MCR/ECR Technical Manual MDS 05-6632A01, Rev. F
SNMPv2-MIB system sysDescr "GE MDS Orbit SNMP Agent"
SNMPv2-MIB system sysObjectID 1.3.6.1.4.1.4130.10
SNMPv2-MIB system sysUpTime 911614
SNMPv2-MIB system sysServices 72
SNMPv2-MIB system sysORLastChange 0
SNMPv2-MIB snmp snmpInPkts 0
SNMPv2-MIB snmp snmpInBadVersions 0
SNMPv2-MIB snmp snmpInBadCommunityNames 0
SNMPv2-MIB snmp snmpInBadCommunityUses 0
SNMPv2-MIB snmp snmpInASNParseErrs 0
SNMPv2-MIB snmp snmpSilentDrops 0
SNMPv2-MIB snmp snmpProxyDrops 0
SNMPv2-MIB snmpSet snmpSetSerialNo 3928852
> show SNMP-FRAMEWORK-MIB
SNMP-FRAMEWORK-MIB snmpEngine snmpEngineID 80:00:10:22:03:00:06:3d:06:ea:96
SNMP-FRAMEWORK-MIB snmpEngine snmpEngineBoots 36
SNMP-FRAMEWORK-MIB snmpEngine snmpEngineTime 9151
SNMP-FRAMEWORK-MIB snmpEngine snmpEngineMaxMessageSize 50000
> show SNMP-USER-BASED-SM-MIB
SNMP-USER-BASED-SM-MIB usmStats usmStatsUnsupportedSecLevels 0
SNMP-USER-BASED-SM-MIB usmStats usmStatsNotInTimeWindows 0
SNMP-USER-BASED-SM-MIB usmStats usmStatsUnknownUserNames 0
SNMP-USER-BASED-SM-MIB usmStats usmStatsUnknownEngineIDs 0
SNMP-USER-BASED-SM-MIB usmStats usmStatsWrongDigests 0
SNMP-USER-BASED-SM-MIB usmStats usmStatsDecryptionErrors 0
> show SNMP-MPD-MIB
SNMP-MPD-MIB snmpMPDStats snmpUnknownSecurityModels 0
SNMP-MPD-MIB snmpMPDStats snmpInvalidMsgs 0
SNMP-MPD-MIB snmpMPDStats snmpUnknownPDUHandlers 0
> show SNMP-TARGET-MIB
SNMP-TARGET-MIB snmpTargetObjects snmpUnavailableContexts 0
SNMP-TARGET-MIB snmpTargetObjects snmpUnknownContexts 0
Network Monitor Service 3.8.19
Understanding
Network monitor service allows the user to configure network monitor operations like interface-monitor
or icmp-echo-monitor. These operations signal whether the operation state is up or down based on the
state of the interface or periodic pinging of a remote host respectively. This signal can then be used by
other applications to do interesting things. For example, routing uses the signal from interface-monitor or
icmp-echo-monitor to add/remove routes that have been configured with verify-reachability check using
that operation. This enables route failover/failback based on the state of the operation. Also, icmp-
monitor-operation can also just be used to generate some periodic traffic towards a specific host.
Configuration
Using the WebUI
Following example shows how to configure icmp-echo-monitor operation for verifying that the link over
NX is working.