3 Programming the Analyzer
List of SCPI Commands
CALCulate:FSCan:MARKer:PEAK:THReshold?
CALCulate:FSCan:MARKer:PEAK:THReshold:STATe ON | OFF | 1 | 0
CALCulate:FSCan:MARKer:PEAK:THReshold:STATe?
CALCulate:FSCan:MARKer[1]|2|...|12:REFerence <integer>
CALCulate:FSCan:MARKer[1]|2|...|12:REFerence?
CALCulate:FSCan:MARKer[1]|2|...|12[:SET]:METer
CALCulate:FSCan:MARKer[1]|2|...|12[:SET]:SLISt
CALCulate:FSCan:MARKer[1]|2|...|12:TO:METer
CALCulate:FSCan:MARKer[1]|2|...|12:TRACe 1 | 2 | 3
CALCulate:FSCan:MARKer[1]|2|...|12:TRACe?
CALCulate:FSCan:MARKer[1]|2|...|12:X <real>
CALCulate:FSCan:MARKer[1]|2|...|12:X?
CALCulate:FSCan:MARKer[1]|2|...|12:Y?
CALCulate:FSCan:SCAN:DISPlay G1 | G2 | OFF
CALCulate:FSCan:SCAN:DISPlay?
CALCulate:FSCan:SLISt:APPend:METer
CALCulate:FSCan:SLISt:DELete:ALL
CALCulate:FSCan:SLISt:DELete:MARKed
CALCulate:FSCan:SLISt:DELete:SIGNal <integer>
CALCulate:FSCan:SLISt:DELete:UNMarked
CALCulate:FSCan:SLISt:LDELta:UPDate
CALCulate:FSCan:SLISt:MARK:ALL
CALCulate:FSCan:SLISt:MARK:CLEar:ALL
CALCulate:FSCan:SLISt:MARK:CLEar:SIGNal <integer>
CALCulate:FSCan:SLISt:MARK:DUPLicates[:ALL]
CALCulate:FSCan:SLISt:MARK:DUPLicates:LOWer
CALCulate:FSCan:SLISt:MARK:DUPLicates:UPPer
CALCulate:FSCan:SLISt:MARK:SIGNal <integer>
CALCulate:FSCan:SLISt:REPLace:METer <integer>
CALCulate:FSCan:SLISt:SET:METer <integer>
CALCulate:FSCan:SLISt:SNAP:METers
CALCulate:FSCan:SLISt:SORT:AUTO ON | OFF | 1 | 0
CALCulate:FSCan:SLISt:SORT:AUTO?
CALCulate:FSCan:SLISt:SORT:DAMPlitude DET1 | DET2 | DET3
CALCulate:FSCan:SLISt:SORT:DAMPlitude ?
CALCulate:FSCan:SLISt:SORT:DLDelta DET1 | DET2 | DET3
CALCulate:FSCan:SLISt:SORT:DLDelta?
CALCulate:FSCan:SLISt:SORT:ORDer ASCending | DESCending
CALCulate:FSCan:SLISt:SORT:ORDer?
CALCulate:FSCan:SLISt:SORT:TYPE FREQuency | DAMPlitude | DLDelta | TIME
CALCulate:FSCan:SLISt:SORT:TYPE?
CALCulate:FSCan:SLISt:ZOOM <integer>
CALCulate:FSCan:SLISt:ZOOM:OUT
CALCulate:FSCan:TRACe[1]|2|3:FAIL?
CALCulate[1]|2:LIMit[1]|2|...|6:COMMent
CALCulate[1]|2:LIMit[1]|2|...|6:COMMent
CALCulate[1]|2:LIMit[1]|2|...|6:CONTrol[:DATA]
CALCulate[1]|2:LIMit[1]|2|...|6:CONTrol[:DATA]
CALCulate[1]|2:LIMit[1]|2|...|6:COPY
CALCulate[1]|2:LIMit[1]|2|...|6:COPY
CALCulate[1]|2:LIMit[1]|2|...|6:DELete
CALCulate[1]|2:LIMit[1]|2|...|6:DELete
CALCulate[1]|2:LIMit[1]|2|...|6:FAIL?
EMI Receiver Mode Reference 73
To Next Page
Loading...
Need help?
General
