Korg TRITON proX User Manual

102
0–1(2)j: PLAY/MUTE, SOLO ON/OFF
PLAY/MUTE [PLAY, MUTE]
This sets the play/mute status of each track. The setting will
alternate each time you press the PLAY/MUTE button.
PLAY: The track will play.
MUTE: The track will be muted.
SOLO ON/OFF [SOLO ON, SOLO OFF]
Switch the Solo function on/off. Only the track set to SOLO
ON will be heard. All other tracks will be muted.
If a track muted by the Mute or Solo function has a
“Status” (1–1a, 2a) of EXT or BTH, the MIDI note-on/
off messages of that track will not be transmitted.
(However, the track selected by “Play Track Select” (0–
1g) is an exception.)
If the page menu command “Solo Selected Track” (0–
1B) is ON, its solo settings will take priority (when ON).
When you press “SOLO ON/OFF” or press a parame-
ter of another track, only that track will be soloed and
will sound.
▼ 0–1: Page Menu Command
0–1A: GM Initialize
This command transmits a GM System On message to Song
Play mode, resetting all tracks to the GM settings (refer to
the table below).
In Song Play mode when a GM System On message is
received from an external device or if the SMF contains
a GM System On message, the tone generator will be
reset to the GM settings in the same way as when this
command is executed (However even in these cases, the
parameters of the P9: Master Effect will not be reset).
0–1B: Solo Selected Track
When you select this command and check the menu page,
only the selected track will sound and the remaining tracks
will be muted (the Solo function). To solo a different track,
select one of the parameters of that track (
☞Sequencer P0: 0–
1B).
If a track muted by the Mute or Solo function has a
“Status” (1–1a, 2a) of EXT or BTH, the MIDI note-on/
off messages of that track will not be transmitted.
0–1C: Load Template Song
This command loads a preset template song (one of sixteen
types P00–15) or a user template song (one of sixteen types
U00–15) into the song (
☞Sequencer P0: 0–1G).
0–1D: Save Template Song
This command saves the programs, the track parameters,
and the effect settings etc. as a user template song U00–15
(
☞Sequencer P0: 0–1H).
The settings that are saved here can also be loaded in
Sequencer mode.
0–1E: Set Location
By pressing the [LOCATE] key you can move to the location
specified here (
☞Sequencer P0: 0–1J).
0–1A
0–1B
0–1C
0–1D
0–1E
Parameter Track1–9, 11–16 Track10
P0 Bank/Program G000:*A.Piano g(d)000:STANDARD KIT
Pan C064 C064
Volume 100 100
P1 Status – – The setting remains unchanged
Use Program’s Scale – – The setting remains unchanged
P7 Arpeggiator Assign – – The setting remains unchanged
Other Arpeggiator parameters – – The setting remains unchanged
P8 IFX/Indiv.Out BUS Select L/R DKit
Send1(MFX1) 0 0
Send2(MFX2) 40 40
IFX1–5 – – The setting remains unchanged
Pan(CC#8) – – The setting remains unchanged
BUS Select – – The setting remains unchanged
Send1 – – The setting remains unchanged
Send2 – – The setting remains unchanged
Other Insert Effect parameters – – The setting remains unchanged
P9 MFX1 – – 016: Stereo Chorus
MFX2 – – 053: Reverb Smooth Hall
Return1 – – 127
Return2 – – 050
Other Master Effect and Master EQ parameters – – Default settings

Korg TRITON proX Specifications

General

Brand	Korg
Model	TRITON proX
Category	Synthesizer
Language	English