Global
P0
P1 P2 P3 P4 P5 P6
115
Drum Kits and User Arpeggio Patterns are written using the
P5 page menu command “Write Drum Kits” and the P6
page menu command “Write Arpeggio Pattern” respec-
tively.
0–1B: Change all bank references
This command changes all program banks specified for tim-
bres in combinations or tracks of songs.
1 Select this command to open the following dialog box.
2 If you wish to change bank references for combinations,
check “Combination.” If you wish to change bank refer-
ences for songs, check “Song.”
3 In “Program Bank,” specify the replacement for each
bank.
4 To execute the Change All Bank References command,
press the OK button. To cancel, press the Cancel button.
If you change two or more different banks to the same
bank, it will not be possible to use this function to
change them back to different banks. Be careful that the
change destination banks do not overlap.
0–1C: Touch Panel Calibration
If input via the LCD screen does not work as you expect, or
if the edit cell moves to a location other than where you
pressed the LCD screen, use this command to adjust the sen-
sitivity of the LCD screen.
1 Select this command to open the following dialog box
☞ If you are unable to select this command from the page
menu, hold down the [ENTER] key and press the [2] key
to access the command.
2 Press the square in the upper left of the LCD. When your
touch has been detected correctly the square will be high-
lighted.
3 Press the square in the lower right of the LCD. When
your touch has been detected correctly the square will be
highlighted.
4 Press the Done button.
If your touch was not detected correctly, an error mes-
sage will appear. Please perform the procedure once
again.
0–1D:
Half Damper Calibration
If the damper pedal effect does not apply correctly when
you are using a half-damper compatible pedal the sepa-
rately sold DS-1H option, use this command to adjust the
sensitivity of the damper pedal.
1 Connect a half-damper pedal to the DAMPER jack.
2 Select this command to open the following dialog box.
3 Press the half-damper pedal, and then release your foot
from the pedal.
4 Press the Done button.
If the adjustment could not be performed correctly, an
error message will be displayed. Please perform the pro-
cedure once again.
Since the half-damper pedal is highly sensitive, please
use the optional DS-1H. Other pedals may not produce
the appropriate effect, or may be impossible to calibrate
correctly.
0–2: System Pref. (System Preference)
0–2a: System Preference
Bank Map [KORG, GM(2)]
Specify the mapping of programs and combinations relative
to Bank Select control change messages (CC#0 upper byte
and CC#32 lower byte).
The following Bank Select messages will be received (R) and
transmitted (T) for Program banks A, B, C, D, E, F (only for
the separately sold EXB-MOSS option, G, g(1)–g(9), and
g(d), and Combination banks A, B, C, and D.
Bank KORG GM(2)
A 00. 00 R/T 3F. 00 R/T
B 00. 01 R/T 3F. 01 R/T
C 00. 02 R/T 3F. 02 R/T
D 00. 03 R/T 3F. 03 R/T
E 00. 04 R/T 3F. 04 R/T
F 00. 05 R/T 3F. 05 R/T
G, 79. 00, 79. 01–09 R/T 79. 00, 79. 01–09 R/T
g(1)–g(9) 38. 00 R 38. 00 R
00. 00, 00. 01.. (XG)R
00. 00, 01. 00.. (GS)R
g(d) 78. 00 R/T 78. 00 R/T
3E. 00 R 3E. 00 R
3F. 7F R→MUTE(Korg Mute)
0–1
0–2a
0–2b
To Next Page
Loading...
Need help?
General
