Combination
P0
P1 P2 P3 P4 P7 P8 P9
33
2–1: MIDI Channel (MIDI Ch)
Here you can make MIDI settings for each timbre.
2–1a: Status, MIDI Channel, Bank Select
Status [INT, Off, EXT, EX2]
☞ Link: “Status” (0–1f).
MIDI Channel [01...16, Gch]
Set the MIDI transmit/receive channel for each timbre 1–8.
Gch: The timbre will use the channel that has been selected
as the global MIDI channel “MIDI Channel” (Global P1: 1–
1a).
When “Status” is INT, MIDI messages will be received on
the channel you specify here. If this setting is the same as the
global MIDI channel, the internal tone generator will sound
according to the internal settings. If this is set to EXT or EX2,
playing the TRITON will transmit MIDI messages on the
MIDI channel specified here. (Messages will also be trans-
mitted simultaneously on the global MIDI channel.)
Bank Select (When Status=EX2) [000:000...127:127]
Specify the bank number that will be transmitted when “Sta-
tus” is set to EX2. If “Status” is not set to “EX2,” this setting
has no effect.
2–2: OSC
These settings specify how each timbre will be sounded.
2–2a: Force OSC Mode, OSC Select, Portamento
Force OSC Mode [PRG, Poly, MN, LGT]
Specify the Voice Assign Mode (Program P1: 1–1b) of the
program selected for each timbre 1–8.
PRG: The settings of the program will be used.
Poly: The timbre will play polyphonically, regardless of the
settings of the program.
MN (Mono): The timbre will play monophonically, regard-
less of the settings of the program.
LGT (Legato): The timbre will play monophonically, with
single triggering (legato).
With settings of MN or LGT, the note priority will be
according to the “Priority” (Program P1: 1–1b) setting of the
program.
OSC Select [BTH, OS1, OS2]
Specify the “Oscillator Mode” of the program selected for
each timbre 1–8. If the “Oscillator Mode” (Program P1: 1–1a)
is Double, you can specify that either or both oscillators
sound.
BTH (Both): OSC1 and 2 will sound as specified by the set-
tings of the program.
OS1: Only OSC1 will sound.
OS2: Only OSC2 will sound. (If “Oscillator Mode” is Single
or Drums, there will be no sound.)
Portamento [PRG, Off, 001...127]
Make portamento settings for each timbre 1–8.
PRG: Portamento will be applied as specified by the pro-
gram settings.
Off: Portamento will be off, even if the original program set-
tings specified for it to be on.
001...127: Portamento will be applied with the portamento
time you specify here, even if it is turned off by the program
settings.
If the “Status” (0–1f, 2–1a) is set to INT, CC#05 (porta-
mento time) and #65 (portamento switch) messages
will be received to control and change this setting. (If
the setting is PRG, #05 portamento time will not be
received.) These messages will be received on the MIDI
channel specified for each timbre by “MIDI Channel”
(2–1a).
2–3: Pitch
Here you can make pitch-related settings for each timbre.
Combination P2: Edit–Trk Param
0–1
MSB
LSB
2–1a
0–1
2–2a
2–3
2–3a
To Next Page
Loading...
Need help?
General
