60
4–3: Vel Z 1–8 (Vel Zone T01–08)
4–4: Vel Z 9–16 (Vel Zone T09–16)
Top/Bottom Velocity specify the range of velocities that will
be sounded by tracks 1–16, and Top/Bottom Slope specify
the range over which the volume will be adjusted.
These settings do not affect MIDI transmission/recep-
tion. All note data that is received will be recorded into
the internal sequencer, and all note data from the inter-
nal sequencer or from the keyboard will be transmitted.
4–3(4)a: Top Velocity, Top Slope
Top Velocity [1…127]
Specify the maximum velocity that will be sounded by each
track 1–16.
Top Slope [0…120]
Specify the range of values over which the volume will be
adjusted from the top velocity until the original volume is
reached.
4–3(4)b: Bottom Slope, Bottom Velocity
Bottom Slope [0…120]
Specify the range of values over which the volume will be
adjusted from the bottom velocity until the original volume
is reached.
Bottom Velocity [1…127]
Specify the minimum velocity that will be sounded by each
track 1–16.
For details on these parameters and on the diagram, refer to
“Combination P4–2: Vel Z (Velocity Zone).”
You can also enter a value for these parameters by play-
ing a note while you hold down the [ENTER] key.
4–5: MOSS 1–8 (MOSS T01–08)
4–6: MOSS 9–16 (MOSS T09–16)
This page is displayed when the separately sold EXB-MOSS
option has been installed. For details refer to the owner’s
manual included with the EXB-MOSS.
4–7: Controller (Controller Setup)
Here you can set the functions that the [SW1] key, [SW2] key,
and the B-mode functions that the REALTIME CONTROL
knobs [1]–[4] will have in Sequencer mode.
When these switches or knobs are operated during
recording, the MIDI messages that you assign here will
be recorded.
4–7a: Panel Switch Assign
Assign functions to the front panel [SW1] and [SW2] keys
(
☞p.217 “SW1, SW2 Assign List”).
Since the functions assigned to these switches and knobs by
the program of each track will not be valid, you can make
new assignments here.
SW1 (SW1 Assign) [Off, ..., After Touch Lock]
SW1 Mode [Toggle, Momentary]
SW2 (SW2 Assign) [Off, ..., After Touch Lock]
SW2 Mode [Toggle, Momentary]
☞ “Panel Switch Assign” (Program P1: 1–4a).
4–7b: Realtime Control Knobs B-Assign
Here you can set the B-mode functions (mainly various con-
trol changes) that the front panel REALTIME CONTROL
knobs [1]–[4] will have in Sequencer mode (
☞p.218 “Real-
time Control Knobs B–Assign List”). The functions you
specify here will operate when you rotate the front panel
REALTIME CONTROL knobs [1]–[4] in B-mode.
Since the functions assigned to these knobs by the program
of each track will not be valid, you can make new assign-
ments here.
Knob 1-B [Off, ..., MIDI CC#95]
Knob 2-B [Off, ..., MIDI CC#95]
Knob 3-B [Off, ..., MIDI CC#95]
Knob 4-B [Off, ..., MIDI CC#95]
☞ “Realtime Control Knobs B-Assign” (Program P1: 1–4b).
0–1c
0–1e
0–1g
0–1
4–3a
4–3b
0–1c
0–1e
0–1g
0–1
4–7a
4–7b
To Next Page
Loading...
Need help?
General
