Korg TRITON proX User Manual

Sequencer
P0
P1 P2 P3 P4 P5 P6 P7 P8 P9
73
Here you can specify how the arpeggiator will operate in
Sequencer mode. These settings can be made for each song.
In Sequencer mode (as in Combination mode), you can run
the two arpeggiators simultaneously. This allows you to
apply different arpeggio patterns to two sounds that have
been split across the keyboard, or use velocity to switch
between two different arpeggio patterns, etc.
In Sequencer mode, the musical data generated by the
arpeggiator during song track or pattern realtime-recording
can be recorded. While you record, you can modify the
arpeggio pattern and parameters, and adjust the [GATE]
knob and [VELOCITY] knob etc.
It is not possible to set the tempo of the arpeggiator and
the sequencer independently.
When “MIDI Clock” (Global P1: 1–1a) is Internal, the arpeg-
giator can be synchronized to the start timing of the internal
sequencer.
• When you turn on the arpeggiator and press the
[START/STOP] key, the arpeggiator will synchronize to
the timing of the sequencer.
• When you press the [START/STOP] key, the
arpeggiator and sequencer will both stop. If you wish to
stop only the arpeggiator, press the ARPEGGIATOR
[ON/OFF] key.
When “MIDI Clock” is External MIDI or External PC I/
F, the MIDI realtime clock messages transmitted from
the external MIDI device connected to MIDI IN or the
TO HOST connector can perform the same type of con-
trol.
Even in this case, you can start/stop using the [START/
STOP] key of the TRITON’s sequencer.
7–1: Setup 1–8 (Setup T01–08)
7–2: Setup 9–16 (Setup T09–16)
7–1(2)a: Arpeggiator Assign, Arpeggiator Run A, B
Arpeggiator Assign [Off, A, B]
This assigns arpeggiator A or arpeggiator B to each track 1–
16. When the front panel ARPEGGIATOR [ON/OFF] key is
turned on, the arpeggiator specified for each track will run,
subject to the “Arpeggiator Run A, B” settings and setting
here.
Off: The arpeggiator will not operate.
A: Arpeggiator A will operate. Use the Arpeggiator A tab to
select the arpeggio pattern and set the parameters.
B: Arpeggiator B will operate. Use the Arpeggiator B tab to
select the arpeggio pattern and set the parameters.
For tracks that you wish to realtime-record, select either
arpeggiator A or B. If you specify an arpeggiator for two or
more tracks, the arpeggiator will play each of the tracks you
specify.
You can set A and B to two different MIDI channels, and
control one from the keyboard and the other from an exter-
nal MIDI device connected to MIDI IN. You can also use
multi-track recording (MultiREC) to simultaneously record
the note data that is generated from the two arpeggiators.
The arpeggiator cannot be triggered by the notes
played by the sequencer.
If the tracks 1–16 assigned to arpeggiators A and B have
a “Status” (2–1a) of INT or BTH, they will be played by
the note data generated by the arpeggiator. If the “Sta-
tus” is BTH, EXT, or EX2, MIDI note data will be trans-
mitted on the “MIDI Channel” of each track.
In this case, arpeggiator A or B will be triggered by the
“MIDI Channel” (2–1a) of any track 1–16 to which the
corresponding arpeggiator is assigned.
If the (“Local Control On” Global P1: 1–1a) is turned
OFF, the arpeggiator will not be triggered by note data
from the keyboard. It will be triggered by note data
received at MIDI IN. If you wish to record just the trig-
ger notes on an external sequencer and run the TRI-
TON’s arpeggiator in this way, turn Local Control OFF.
If you want the note data generated by the arpeggiator
to be recorded on the external sequencer, turn Local
Control ON, and turn off the echo back function of the
external sequencer.
Example 1)
On tracks 1 and 2, set “MIDI Channel” (2–1a) to 01 and
“Status” (2–1a) to INT. Assign arpeggiator A to track 1
and arpeggiator B to track 2, and check “Arpeggiator
Run A, B” (7–1a). In “Track Select,” choose Track01.
With the front panel ARPEGGIATOR [ON/OFF] key
OFF, play the keyboard and tracks 1 and 2 will sound
simultaneously.
When you turn on the front panel ARPEGGIATOR [ON/
OFF] key and play the keyboard, arpeggiator A will
operate for track 1 and arpeggiator B will operate for
track 2.
Sequencer P7: Arpeggiator
0–1a
.
.
.
0–1g
7–1
7–1a
Track2 MIDI Ch=1ch Status=INT
Arpeggiator
A
Arpeggiator
B
Arpeggiator
Assign
A
B
Pattern - A
Pattern - B
Pattern - A
Pattern - B
Trigger
= Ch1
Trigger
= Ch1
Track1 MIDI Ch=1ch Status=INT

Korg TRITON proX Specifications

General

Brand	Korg
Model	TRITON proX
Category	Synthesizer
Language	English