Korg TRITON proX User Manual

76
Send1 (MFX1) [000...127]
Send2 (MFX2) [000...127]
Here you can adjust the send levels from tracks 1–16 to mas-
ter effects 1 and 2. This is valid when “BUS Select” is set
either to L/R or Off. If IFX 1, 2, 3, 4, or 5 is selected, the send
level to the master effects 1 and 2 is set by the “Send 1” and
“Send 2” parameters located in the Insert FX tab, after the
signal passes through IFX 1–5.
These settings have no effect if “BUS Select” is set to 1, 2, 3,
4, 1/2 or 3/4.
The send 1 and 2 settings you make here will be used when
the song is played or recorded from the beginning. If you
change the settings while recording, the change will be
recorded as part of the musical data, and the send amount
will change when the data is played back. You can also
change these settings during playback. However if send 1
and 2 data has been recorded, the settings will change
accordingly.
If “Status” (2–1a) is either INT or BTH, CC#93 and #91
can be received to control send 1 and 2 respectively and
change their settings. When you switch songs or return
to the beginning of a song, tracks whose “Status” is
EXT, EX2 or BTH will transmit these settings via MIDI.
This data will be transmitted on the MIDI channel of
each track as set by “MIDI Channel” (2–1a). The actual
send level is determined by multiplying the value of
these parameters with the send level settings of the
oscillator(s) of the program used by the track (“Send1”
and “Send2,” Program P8: 8–1d).
▼ 8–1: Page Menu Command
8–1A: Copy Insert Effect
☞ “Program P8: 8–1A: Copy Insert Effect.”
However, the MIDI control channel specified in “Ctrl Ch” of
the IFX 1–5 tab will not be copied.
8–1B: Swap Insert Effect
☞ “Program P8: 8–1B: Swap Insert Effect.”
However, the MIDI control channel specified in “Ctrl Ch” of
the IFX 1–5 tab will not be swapped.
8–1C: DrumKit IFX Patch
☞ “Combination P8: 8–1C: DrumKit IFX Patch.”
8–3: Insert FX
Here you can select the type of the insert effects, turn them
on/off, and make chain settings.
These functions are the same as in Program mode. Please
refer to Program mode “8–2: Insert FX.”
However, unlike the case in Program mode, “Pan (CC#8),
“Send 1(MFX1)” and “Send 2 (MFX2)” will be controlled by
the MIDI channels specified in each of the IFX 1–5 tabs. The
control changes used are the same as in Program mode.
The pan (CC#8), send 1 and 2 settings you make here will be
used when the song is played or recorded from the begin-
ning. If you change the settings while recording, the changes
will be recorded as part of the musical data, and the settings
will change when the data is played back. You can also
change these settings during playback. However if pan
(CC#8), send 1, or 2 data has been recorded, the settings will
change accordingly.
If “Status” (2–1a, 2a) is either INT or BTH, CC#8, #93,
and #91 can be received to control the pan following the
insert effect, send 1, or send 2 respectively, and change
their settings. When you switch songs or return to the
beginning of the song, tracks whose “Status” is BTH,
EXT, or EX2 will transmit these settings via MIDI. This
data will be transmitted on the MIDI channels specified
in the IFX 1–5 tabs (8–4 – 8–8).
8–4: IFX 1
8–5: IFX 2
8–6: IFX 3
8–7: IFX 4
8–8: IFX 5
Set the parameters for the effects selected for IFX 1–5 in the
Insert FX tab (
☞p.155).
0–1A
0–1B
8–1A
8–1B
8–1C
0–1I
0–1J
0–1e
8–1
8–4a
0–1A

Korg TRITON proX Specifications

General

Brand	Korg
Model	TRITON proX
Category	Synthesizer
Language	English