Program
P0
P1 P2 P3 P4 P5 P7 P8 P9
11
when the [SW1] key is turned on. The direction of the
change is specified by “St” and “At.” When the [SW1] key is
turned off, the pitch EG levels will return to their own set-
tings.
If “AMS1” is set to Velocity, increasing the absolute value of
“Intensity” will produce increasingly wider change in pitch
EG levels for strongly-played notes. The direction of the
change is specified by “St” and “At.” As you play more
softly, the pitch change will draw closer to the pitch EG lev-
els.
St (AMS1 SW to Start) [–, 0, +]
Specify the direction of change in “Start (Start Level)”
caused by “AMS1.” If “Intensity” is a positive (+) value, a
setting of + will raise the EG level, and a setting of – will
decrease it. With a setting of 0 there will be no change.
At (AMS1 SW to Attack) [–, 0, +]
Specify the direction of change in “Attack (Attack Level)”
caused by “AMS1.” If “Intensity” is a positive (+) value, a
setting of + will raise the EG level, and a setting of – will
decrease it. With a setting of 0 there will be no change.
AMS2 (Alternate Modulation Source 2) [Off, (KT, EXT)]
Intensity (AMS1 Intensity) [–99…+99]
St (AMS2 SW to Start) [–, 0, +]
At (AMS2 SW to Attack) [–, 0, +]
Refer to the preceding paragraphs “AMS1”–“At.”
2–3c: Time Modulation
These parameters let you use alternate modulation to con-
trol the “Time” parameters of the pitch EG.
AMS (Alternate Modulation Source) [Off, (KT, EXT)]
Select the source that will control the “Time” parameters of
the pitch EG (
☞p.210 “AMS (Alternate Modulation Source)
List”).
Intensity [–99…+99]
Specify the depth and direction of the effect that “AMS” will
have.
With a setting of 0, the pitch EG times will be just as speci-
fied by the “Pitch EG” (2–3a) settings.
The alternate modulation value at the moment that the EG
reaches each point will determine the actual value of the EG
time that comes next.
For example, the decay time will be determined by the alter-
nate modulation value at the moment that the attack level is
reached.
When this parameter is set to values of 16, 33, 49, 66, 82, or
99, the specified EG times will speed up as much as 2, 4, 8,
16, 32, or 64 times respectively (or slowed down to 1/2, 1/4,
1/8, 1/16, 1/32, or 1/64 of the original time).
For example if “AMS1” is set to Velocity, increasing the
absolute value of “Intensity” will allow strongly-played
notes to increase the changes in pitch EG “Time” values. The
direction of the change is specified by “At” and “Dc.” As
you play more softly, the pitch EG times will more closely
approach the actual settings of the pitch EG.
At (AMS SW to Attack) [–, 0, +]
Specify the direction in which “AMS” will affect the “Attack
(Attack Time).” With positive (+) values of “Intensity,” a set-
ting of + will cause the time to be lengthened, and a setting
of – will cause the time to be shortened. With a setting of 0
there will be no change.
Dc (AMS SW to Decay) [–, 0, +]
Specify the direction in which “AMS” will affect the “Decay
(Decay Time).” With positive (+) values of “Intensity,” a set-
ting of + will cause the time to be lengthened, and a setting
of – will cause the time to be shortened. With a setting of 0
there will be no change.
▼ 2–3: Page Menu Command
☞ “0–1A: Write Program,” “1–1A: Copy Oscillator,” and “1–
1B: Swap Oscillator.”
Pitch EG change (level) (AMS=SW1/Velocity, Intensity= positive (+) value
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
A note played softly with St
set at 0, At set to +, and
SW1 turned on (the settings
of 2–3a: Pitch EG)
A note played strongly with
St set to 0, At set to +, and
SW1 turned on
A note played strongly with
St set to 0, At set to –, and
SW1 turned on
Pitch EG changes (Time) (AMS = Velocity, Intensity = positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
A note played softly with At
set to + and Dc set to +
(settings of 2–3a: Pitch EG)
A note played strongly with
At set to + and Dc set to +
A note played strongly with
At set to – and Dc set to –
To Next Page
Loading...
