Motion Control Engineering 2000 - Page 292

Index-10 Manual # 42-02-1P21
SC-3HN board 6-70
SCE, Stepping correction enable flag 5-11
schematic symbols, description of 2-6
SCROLLING SPEED option 5-53
SD, Supervisory down flag 5-11
SDA, Down direction arrow flag 5-11
SDT, Short door time flag 5-11
SDTR, Short door time (rear) flag 5-11
SE, Safety edge input flag 5-11
SEC, Security Code Incorrect Output 5-46
SECONDARY PARKING FLOOR option 5-19
security 5-5
SEQUENTIAL DOOR OPER. (F/R) option 5-22
SER, Safety edge input (rear) flag 5-11
SERIAL CARTOP DOOR CNTRL option 5-19
SERIAL COP BOARD HC-CPI option 5-19
Serial Hall Call Node Board 6-70
set parameters to default values 5-13
setting the date and time 5-70
SHORT DOOR TIMER 5-26
short floor 3-21
SIMP, Simplex Input 5-37
SIMPLEX/LOCAL OR DUPLEX option 5-17
SIMPO, Simplex Output 5-46
SLV, Stable slave flag 5-11
Smoothing tape edges 3-12
Soft Stop operation 4-6
SOFT-STOP TIMER option 5-54
Software version
CHP 5-107
CTLA 5-107
CTLB 5-107
CTLC 5-107
MPIA 5-107
MPUA 5-107
UIO 5-107
Software Version, viewing 5-106
SPA IS OFFLINE message 6-34
Spare Inputs Menu Options ??–5-38
SPARE OUTPUTS MENU OPTIONS 5-39
Spare Outputs Menu Options ??–5-47
SPB IS OFFLINE message 6-35
SPD0 6-42
SPD1 6-42
SPD2 6-42
SPEED > 150 FPM? option 5-55
SST, Soft stop timer flag 5-11
STARTER #1 TYPE option 5-54
STARTER #2 TYPE option 5-54
STARTER #3 TYPE option 5-54
STARTER CONFIG
(SEQUENTIAL / SIMULTANEOUS) option 5-54
STARTER FAULT CONTACT OPEN message 6-35
STARTER TYPE ERROR message 6-35
STARTIN, Start Input 5-37
Status and Error Messages 6-3–6-36
Status Displays 5-106
Current load 5-106
Eligibility map 5-106
Software Version 5-106
STC, Stepping complete flag 5-11
STD/R0, Step down input/absolute floor encoding #0 flag
5-11
STDX 5-37
Steel tape 3-12
Step Dn1 5-103
Step Down, 209 5-105
Step Up, 210 5-105
Step Up1 5-103
Stepping System 5-103
Stepping System, 208 5-105
Stick alignment 3-15
Stop SW/Safety Relay Ckt message 6-21
STU/R1, Step up input/absolute floor encoding #1 flag 5-11
Stuck Door Zone Input message 6-10
Stuck Leveling Input message 6-22
STUCK PHOTO EYE PROTECTION option 5-22
STUX 5-37
SU, Supervisory up flag 5-11
SUA, Up direction arrow flag 5-11
Sub Step DN1 5-103
Sub Step UP1 5-103
Subnet mask screen 5-98
Sub-step Down, 241 5-105
Sub-step Up, 242 5-105
SWG 5-37
SYNC, Synchronization Output 5-46
SYNC. OP. DELAY TIMER 5-28
Synchronization Operation message 6-35
SYNCI, Synchronization Input 5-38
System CAN Bus 5-97
System Mode 5-60–5-66
T
TAB1 6-41
Tape cleaning 3-12
TEMPB, Temporary bit flag 5-11
Temporary run box wiring 3-6
Test Mode 1-19
Test mode operation 4-4
Test mode, description 4-4
TEST, Test Switch Input 5-38
TEST, Test switch input flag 5-11
TESTSWO, Test switch output 5-46
TFA, Timing function active flag 5-11
TFAR, Timing function active (rear) flag 5-11
TFD, Top floor demand flag 5-11
TFTP Status screen 5-99
Time Out of Service message 6-35
Timer Menu options 5-26–5-27
Top Access Distance 5-104
TOP ACCESS SW. FAILURE message 6-35
TOP ACCESS? (F/R) option 5-54
TOP LANDING FOR OTHER CAR? option 5-18
TOP LANDING SERVED? option 5-18
Top Terminal Test 4-10
TOS, Timed out of service flag 5-11
TOS, Timed Out of Service Output 5-47