RADWAG PUE HY10

7
35.2. Deleting older data ................................................................................................................................. 198
35.3. Weighment date search ......................................................................................................................... 198
35.4. Reports from weighment records ........................................................................................................... 199
35.4.1. Filtering........................................................................................................................................ 199
35.4.2. Report printout ............................................................................................................................ 200
35.4.3. Weighments chart ....................................................................................................................... 201
35.4.4. Export a database to a file .......................................................................................................... 202
35.4.5. Counter of weighments records .................................................................................................. 204
35.5. Reports preview ..................................................................................................................................... 205
35.5.1. Weighments / Alibi ...................................................................................................................... 205
35.5.2. Reports from dosing .................................................................................................................... 206
35.5.3. Reports from recipes ................................................................................................................... 207
35.5.4. Density reports ............................................................................................................................ 208
35.5.5. Controls reports........................................................................................................................... 209
35.5.6. Average tare reports ................................................................................................................... 210
35.5.7. Report from vehicle scale ........................................................................................................... 212
35.5.8. Differential weighments reports .................................................................................................. 212
36. IDENTIFICATION PROCESSES ................................................................................................................. 213
36.1. Identification process – creation ............................................................................................................ 214
36.2. List of identification process functions ................................................................................................... 215
36.3. Identification process – activation procedure ........................................................................................ 217
36.3.1. Activation by programmable button ............................................................................................ 217
36.3.2. Activation by operator logging .................................................................................................... 218
36.3.3. Activation by product selection ................................................................................................... 218
36.3.4. Example of process forming and its realization .......................................................................... 219
37. COMMUNICATION PROTOCOL ................................................................................................................. 222
37.1. General information................................................................................................................................ 222
37.2. List of RS commands ............................................................................................................................. 223
37.3. Respond message format ...................................................................................................................... 224
37.4. Command’s description ......................................................................................................................... 224
37.4.1. Zeroing ........................................................................................................................................ 224
37.4.2. Tarring ......................................................................................................................................... 225
37.4.3. Get tare value .............................................................................................................................. 225
37.4.4. Set tare value .............................................................................................................................. 225
37.4.5. Send the stable result in basic unit ............................................................................................. 226
37.4.6. Send the result immediately in basic unit ................................................................................... 226
37.4.7. Send immediate results from all platforms in basic units ........................................................... 227
37.4.8. Send the stable result in current unit .......................................................................................... 227
37.4.9. Send the result immediately in current unit ................................................................................ 228
37.4.10. Switch on continuous transmission in basic unit ...................................................................... 229
37.4.11. Switch off continuous transmission in basic unit ...................................................................... 229
37.4.12. Switch on continuous transmission in current unit ................................................................... 229
37.4.13. Switch off continuous transmission in current unit ................................................................... 230
37.4.14. Set lower threshold ................................................................................................................... 230
37.4.15. Set upper threshold .................................................................................................................. 230
37.4.16. Read lower threshold ................................................................................................................ 230
37.4.17. Read upper threshold ............................................................................................................... 231
37.4.18. Simulation of pressing ENTER/PRINT key .............................................................................. 231
37.4.19. Change platform ....................................................................................................................... 231
37.4.20. Give balance serial number ...................................................................................................... 232
37.4.21. Set mass value of a single item ................................................................................................ 232
37.4.22. Set reference mass value ......................................................................................................... 232
37.4.23. Activate sound signal ................................................................................................................ 233
37.4.24. Give available working modes .................................................................................................. 233
37.4.25. Set working mode ..................................................................................................................... 234
37.4.26. Give current working mode ....................................................................................................... 235
37.4.27. Send all implemented commands ............................................................................................ 235
37.5. Manual printouts / automatic printouts ................................................................................................... 236
38. MODBUS RTU COMMUNICATION PROTOCOL ....................................................................................... 236
38.1. Memory map .......................................................................................................................................... 238
38.1.1. Output address............................................................................................................................ 238
38.1.2. Input address .............................................................................................................................. 239
38.2. Description of variables .......................................................................................................................... 239
38.2.1. Output variables .......................................................................................................................... 239
38.2.2. Input variables ............................................................................................................................. 243