What to do if eLevel error appears on SICK DL100?
If the current damping value is below the warning threshold on your SICK Measuring Instruments device (eLevel), you should: * Clean external lens surfaces like the reflector and the lens. * Decrease the distance between the measuring device and the reflector. * Use a distance measuring device with a higher range.
Why are LED BF flashing red and LED SF lit red on SICK Measuring Instruments?
If the LED BF flashes red and the LED SF is lit red on your SICK Measuring Instruments device, it means the device (slave) is not configured or not configured correctly, and no data is being exchanged. You should configure the device and check the configuration.
How to troubleshoot SICK Measuring Instruments displaying '0000'?
If the SICK Measuring Instruments display shows "0000", it could be due to several reasons: * The measuring device's light spot isn't hitting the reflector. To fix this, correct the alignment between the measuring device and the reflector. * There's an obstacle in the light path. Remove any obstacles blocking the light. * The distance between the device and the reflector exceeds the maximum scanning range. Decrease the distance or select a device with a larger scanning range.
What to do if ePlb error appears on SICK DL100?
If the measured value is not plausible (ePlb) on your SICK Measuring Instruments, it may be because the light path between the measuring device and reflector is interrupted or due to optical interferences. To resolve this: * Observe the light spot on the reflector to ensure it doesn't move from the reflector. Re-align the measuring device and reflector if needed, or use a larger reflector. * Remove any optical interferences, and re-align the distance measuring device and reflector.
What to do if 'Device error' appears on SICK Measuring Instruments?
If you see the 'Device error' on your SICK Measuring Instruments, it could be due to hardware issues or the internal device temperature being outside the permissible range. Here's what you can do: * Check the supply voltage and wiring. * Switch the supply voltage on and off. * Wait for the warm-up phase or let the device cool down. * Check the ambient temperature and improve ventilation if needed. * Shield against radiation heat by shading the device from direct sunlight. * Consider using a device with heating for low ambient temperatures or cooling housings for high temperatures. * If the problem persists, send the measuring device in for repair.
How to fix '0000' value on SICK DL100 Measuring Instruments display?
If the display of SICK Measuring Instruments shows "0000", it might be because: * The measuring device's light spot does not hit the reflector. Correct the alignment between the measuring device and the reflector. * There is an obstacle in the light path. Remove any obstacles from the light path. * The distance between the distance measuring device and the reflector exceeds the maximum scanning range. Decrease the distance or select a device with a larger maximum scanning range.
What to do if wTemp error appears on SICK DL100?
If the internal temperature of the SICK Measuring Instruments device is close to the permissible range: * Check the ambient temperature and improve ventilation if applicable. * Shield against radiation heat, e.g. share the measuring device in case of direct solar irradiation. * Use device with heating at low ambient temperatures. * Use cooling housings for high ambient temperatures.
What to do if eTemp error appears on SICK Measuring Instruments?
If the internal temperature of the SICK Measuring Instruments device is outside the permissible range, take the following steps: * Check the ambient temperature and improve ventilation if possible. * Shield against radiation heat, for example, shade the measuring device in case of direct solar irradiation. * Use a device with heating at low ambient temperatures. * Use cooling housings for high ambient temperatures.
What to do if LED PWR is off but the display is lit on SICK DL100?
If the LED PWR is not lit but the display is on for your SICK Measuring Instruments, the measuring device may be defective. Send the device in for repair.
What does 'wLaser' mean on SICK DL100?
The error message 'wLaser' on your SICK Measuring Instruments means that the measurement laser is still working but is nearing the end of its service life. Keep a replacement device ready.
Critical safety information for device operation, including laser safety.
Basic details about the manual, symbols, liability, delivery, and service.
Comprehensive safety rules, intended/non-intended use, and personnel requirements.
Information for identifying the device, including the type label.
Guidance on physical setup, operational principles, display, and controls.
Procedures for safe transport, inspection, and storage of the device.
Detailed steps and considerations for installing the distance measuring device.
Safety precautions and diagrams for connecting the device electrically.
Instructions for device operation, parameter selection, and value changes.
Configuration and operation using the Ethernet interface and SOPAS ET.
Comprehensive guide to CANopen communication, configuration, and objects.
Procedures for cleaning and routine maintenance of the device.
Diagnosing and resolving common issues using LED status, warnings, and errors.
Information on repair policies and detailed technical specifications.
Details on available accessories like reflectors, cables, and mounting systems.
Visual representation of the device's navigation hierarchy and parameters.
General| Wave length | 650 nm |
|---|---|
| Resolution | 0.1 mm |
| Output signal | Analog |
| Supply voltage | 10 V DC ... 30 V DC |
| Beam Diameter | 3 mm |
| Operating Temperature | -10 °C ... +50 °C |
| Storage Temperature | -25°C to +70°C |
| Power Supply | DC |
To Next Page