Name: Siemens sinamics dcp
Brand: Siemens
Rating: 4 (1 reviews)

3 Preparations for use27

4 Mounting31

5 Electrical connection35

6 Commissioning121

7 Operation155

7.1 Operation155
- 7.1.1 Basics155
- 7.1.2 Parameter assignment via the BOP20 (Basic Operator Panel 20)173
7.2 Inputs/outputs183
- 7.2.1 Overview of the inputs/outputs183
- 7.2.2 Digital inputs/outputs183
- 7.2.3 Analog inputs184
- 7.2.4 Analog outputs184
7.3 Communication, IT security185
7.4 Communication according to PROFIdrive185
- 7.4.1 General Information185
- 7.4.2 Application classes189
- 7.4.3 Cyclic communication189
- 7.4.4 Parallel operation of communication interfaces195
- 7.4.5 Acyclic communication198
- 7.4.6 Diagnostic channels213
  - 7.4.6.1 PROFINET-based diagnostics214
  - 7.4.6.2 PROFIBUS-based diagnostics217
7.5 Communication via PROFIBUS DP222
- 7.5.1 General information about PROFIBUS222
  - 7.5.1.1 General information about PROFIBUS for SINAMICS222
  - 7.5.1.2 Example of a telegram structure for cyclic data transfer224
- 7.5.2 PROFIBUS connection225
- 7.5.3 Commissioning PROFIBUS227
- 7.5.4 Direct data exchange232
- 7.5.5 Messages via diagnostics channels245
7.6 Communication via PROFINET IO248
- 7.6.1 General information about PROFINET IO248
- 7.6.2 Establishing online operation: STARTER via PROFINET IO258
- 7.6.3 RT classes for PROFINET IO265
- 7.6.4 PROFINET GSDML270
- 7.6.5 Communication with CBE20271
- 7.6.6 Media redundancy272
- 7.6.7 Messages via diagnostics channels273
- 7.6.8 Support of I&M data sets 1...4275
7.7 Communication via Modbus TCP277
- 7.7.1 Overview277
- 7.7.2 Configuring Modbus TCP via interface X1400279
- 7.7.3 Mapping tables280
- 7.7.4 Write and read access using function codes282
- 7.7.5 Communication via data set 47285
- 7.7.6 Communication procedure289
- 7.7.7 Messages and parameters290
7.8 Communication via EtherNet/IP (EIP)291
- 7.8.1 Components to connect SINAMICS DCP with EtherNet/IP291
- 7.8.2 Configuration of SINAMICS DCP for EtherNet/IP291
- 7.8.3 Communication with the SINAMICS DCP294
  - 7.8.3.1 Implicit messaging – cyclic communication as I/O slave294
  - 7.8.3.2 Explicit messaging - acyclic or event-driven communication297
- 7.8.4 Configuration of a Rockwell controller with SINAMICS DCP307
  - 7.8.4.1 Reading and writing parameters using the Parameter Object (Class code 4xx hex)310
- 7.8.5 Messages and parameters312
7.9 Communication via SINAMICS Link313
- 7.9.1 Basic principles of SINAMICS Link313
- 7.9.2 Topology315
- 7.9.3 Configuring and commissioning316
- 7.9.4 Example321
- 7.9.5 Communication failure when booting or in cyclic operation323
- 7.9.6 Examples: Transmission times for SINAMICS Link324
- 7.9.7 Function diagrams and parameters324
7.10 Switch on, switch off, enable325
- 7.10.1 Switch on / switch off (ON/OFF1) - control word bit 0325
- 7.10.2 OFF2 (disconnection) - control word bit 1326
- 7.10.3 OFF 3 (disconnection) - control word bit 2326
- 7.10.4 Operation enable (enable) - control word bit 3327
7.11 Closed-loop control328
- 7.11.1 General information328
- 7.11.2 Setpoint specification for current control330
- 7.11.3 Current correction controller331
- 7.11.4 Dynamic overload capability331
- 7.11.5 Current limitation and power limitation338
- 7.11.6 Voltage limitation344
- 7.11.7 Dynamic voltage limitation344
- 7.11.8 Voltage control344
- 7.11.9 Voltage correction controller346
- 7.11.10 Current control347
- 7.11.11 Pulse width modulation (PWM)348
- 7.11.12 PV array flying restart349
- 7.11.13 Switching frequency351
- 7.11.14 Actual value acquisition351
- 7.11.15 Actual value adjustment on site352
7.12 Precharging of the DC links353
7.13 Device fan358
7.14 Derating359
7.15 Runtime (operating hours counter)362
7.16 Diagnostics363
- 7.16.1 Diagnostic memory363
- 7.16.2 Description of the LEDs on the CUD364
- 7.16.3 Faults and alarms367
7.17 CPU time load with SINAMICS DCP374
- 7.17.1 Maximum configuration376
7.18 Free function blocks377
7.19 Drive Control Chart (DCC)379
- 7.19.1 Loading the DCC technology option into the drive unit memory380
- 7.19.2 CPU time load through DCC382
- 7.19.3 Memory load through DCC383
- 7.19.4 Backing up the DCC diagrams384
7.20 Write and know-how protection385
- 7.20.1 Write protection385
- 7.20.2 Know-how protection387
- 7.20.3 Overview of important parameters399
7.21 Technological functions400
- 7.21.1 MPP Tracker400
- 7.21.2 Battery charging characteristic405
7.22 Connecting several SINAMICS DCPs in parallel406

8 Servicing417

9 Disposal425

9.1 Environmental compatibility425

10 Technical specifications427

A Appendix433

Index447

Brand	Siemens
Model	sinamics dcp
Category	Media Converter
Language	English

Siemens sinamics dcp Operating Instructions

Table of Contents

Other manuals for Siemens sinamics dcp

Questions and Answers:

Siemens sinamics dcp Specifications

Related product manuals